Enterasys Networks A2H124-48P, A2H124-24P manual Chassis Bottom, Rubber Feet Placement

Page 34

Installing the Switch on a Flat Surface

Figure 3-1 Chassis Bottom, Rubber Feet Placement

Á	À
Â	Â
Â	Â

1Bottom of chassis as seen when chassis is resting on its back

2Locations to install the rubber feet (four locations)

3Rubber feet with adhesive backing (four)

Note: If a number of switches are being installed in a stack, repeat steps 1 through 4 to install the rubber feet on each switch before continuing with the installation.

3-4 Hardware Installation

Image 34

Contents SecureStack A2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Page Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures MGBIC-08 About This Guide Who Should Use This GuideHow to Use This Guide Related DocumentsConventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction Overview A2H124-24P and A2H124-48PA2H124-24P Stackable Switch BackRedundant Power Supply Capability PoE Power over Ethernet SupportStack Connections Connectivity Power Device Classifications UsageDescription of Mini-GBICs Management Switch Configuration Using WebViewSwitch Configuration Using CLI Commands Standards CompatibilityLanview Diagnostic LEDs Getting HelpGetting Help Introduction Network Requirements 10BASE-T Network1000BASE-FX Network 100BASE-TX Network1000BASE-T Network Hardware Installation Contents of Switch Carton Considerations Prior to InstallationUnpacking the Switch Required ToolsInstalling the Switch on a Flat Surface Installing the Rubber FeetChassis Bottom, Rubber Feet Placement Guidelines for Flat Surface Installation Area Guidelines for Switch Installation on Flat SurfaceGuidelines for Rackmount Installation Rack Mounting the SwitchAttaching Brackets and Installing in Rack Connecting Stacking Cables Fastening the Switch to the RackStacking Cable Connections Configuring Switches in a Stack About SecureStack A2 Switch Operation in a StackRecommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesImportant Considerations About Using Clear Config in a Stack Connecting AC and PoE Power AC PowerC2RPS-PoE Redundant Power System Accessing the RPS connectorConnecting to Console Port for Local Management Stack Initialization OverviewWhat Is Needed DB9 Male Console Port Pinout AssignmentsConnecting to an IBM or Compatible Device Connecting an IBM PC or CompatibleConnecting to a VT Series Terminal 10 Connecting a VT Series TerminalConnecting to a Modem 11 Connecting to a ModemConnecting to the Network Connecting UTP Cables12 Connecting a UTP Cable Segment to RJ45 Port 13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX Installing Optional Mini-GBICs Preparation 17 Mini-GBIC with RJ45 Connector 18 Mini-GBIC with MT-RJ Connector 19 Mini-GBIC with LC Connector Removing the Mini-GBICConnecting Fiber-Optic Cables to MT-RJ Ports Installing Optional Mini-GBICs A2H124-24P Connecting Fiber-Optic Cables to LC Ports 21 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using Lanview Lanview LEDs of A2H124-24PLanview LEDs Color State Recommended ActionDown RPS LED Troubleshooting Checklist Configuration Guide for proper setupConfiguration Guide for the IP address Using the Reset Password Switch Reset Password SwitchUsing the Reset Password Switch Troubleshooting Switch Specifications Table A-1 A2H124-24P Switch SpecificationsPhysical EnvironmentalTable A-2 A2H124-48P Switch Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Mini-GBIC Input/Output SpecificationsGigabit Ethernet Specifications Table A-3 Mini-GBIC Input/Output Port SpecificationsMGBIC-LC03 Specifications 1000BASE-SX Table A-10 MGBIC-08 Optical Specifications 10 µm SMF MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX Table A-11 MGBIC-08 Operating Range 1550 nmTable A-12 MGBIC-02 Specifications MGBIC-02 Specifications 1000BASE-TConsole Port Pinout Assignments Regulatory Compliance Table A-13 Compliance Standards Regulatory ComplianceIndex Pinout assignments console port A-7