Enterasys Networks ELS10-27TX manual LCM Command Summary, Subset of LCM Commands

Page 32

Enhancements to LCM Commands

Parameters that appear in all capital letters, for example workgroups [PORT-RANGE], indicate that you must enter a value for that parameter. If a string of parameters is displayed between braces, for example [name {addPORT-RANGE}], you must select one of the displayed options. For example, if you wanted to add ports to a workgroup, you would enter:

ELS10-27>workgroup alpha add 23, 24

For example, if you wanted to add a range of ports in a workgroup, you would enter:

ELS10-27>workgroup omega add 2-18

For a complete list of commands, refer to the SmartSTACK Ethernet ELS10- 27TX User Guide.

2.3 LCM COMMAND SUMMARY

This section contains a subset of LCM commands and syntax.

2.3.1 Subset of LCM Commands

The following is a subset of LCM commands and definitions.

Use ...	To ...


help or ?	display this menu

ipaddr [IPADDR [MASK]]	set or display IP addresses

port [? for syntax]	set or display port parameters

reboot [? for syntax]	reboot the unit after SECONDS

switch [? for syntax]	set or display switch parameters

vlan [? for syntax]	configure IEEE Vlans

workgroup [? for syntax]	set or display workgroups

2-2

Image 32

Contents SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Configuring Vlans Using Snmp Vlan MIB ObjectsXiii Configuring Workgroups Using LCM Configuring Workgroups Using SnmpWorkgroup MIB Objects Appendix a Virtual Lans Vlans IndexAbout this Supplement Getting Help Your email addressDocument Conventions Related Documentation Document Title Part NumberUsing Vlans on the ELS10-27TX Product OverviewIeee 802.1Q Standard Vlan Access Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Hybrid Ports 802.1Q Mode 3 802.1Q Trunk Ports Preserving PriorityAccessing Network Management Using VLANs Non-Preserving PriorityAssigning Ports to a Vlan Switch ModeDefault Port Vlan ID Restricting VLANs 802.1Q Mode Enable GvrpVirtual Workgroups will only operate in 802.1D mode WorkgroupsDefault Gateway Installation and ManagementPage Overview LCM ConventionsLCM Command Summary Subset of LCM CommandsLCM Command Syntax Basic LCM Commands HelpErase Exit or LogoutLCM Commands Enable Command Address LimitRoute Command Port Command Port CommandEnhancements to LCM Commands Switch Command Trap Control Command Vlan Command ELS10-27vlan add 5-9 bluePage Configuring Vlans Using Snmp Overview Config TableModifying a Vlan Modifying, Creating and Deleting VLANsStep Action Creating a Vlan Deleting a VlanConfig Egress List Modifying a Config Egress List Entry Filter Gvrp Table Modifying, Creating or Deleting a Filter Gvrp Table EntryCreating a Filter Deleting a FilterDeleting a Static MAC Entry Static MAC EntryCreating a Static MAC Entry Bridge Configuration Vlan Version NumberOperating Mode VlanOperatingMode Reset VlanResetGvrp Enable VlanGVRPEnable Syntax Octet String SizeAccess List VlanAccessList Vlan VlanConfigVlanVlanConfigEntry Configuration EntriesEntry VlanConfigEntry Index VlanConfigIndex VID VlanConfigVIDPorts VlanConfigPorts IP VlanConfigIPIP Mask VlanConfigIPMask Name VlanConfigNameStatus VlanConfigStatus Establish VlanConfigEstablishActive VlanNumActiveEntries Static Configured VlanNumConfiguredEntriesDevice Entries Configuration Table VlanConfigTable Maximum Number VlanMaxNumEntriesEgress Table Egress Table VlanConfigEgressTable Egress Entry VlanConfigEgressEntryVlanConfigEgressEntry Index VlanEgressIndexVID VlanEgressVID List VlanEgressListStatus VlanEgressStatus Entry VlanFilterGVRPEntry Filter GvrpGvrp VlanFilterGVRPTable VlanFilterGVRPIndex VlanFilterGVRPEntryVID VlanFilterGVRPVID List VlanFilterGVRPListStatus VlanFilterGVRPStatus EstablishVID VlanFilterGVRPEstablishVIDEntry VlanStaticEntry Static MAC Address EntriesTable VlanStaticTable VID VlanStaticVID VlanStaticEntryMAC VlanStaticMAC Port VlanStaticPortEstablish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Configuration Examples Workgroup DefaultWorkgroup Superset LCM Workgroup Commands Workgroups are only valid in 802.1D modeELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Next Number WorkGroupNextNumber Workgroups Using SnmpChapter Workgroup MIB Objects Overview Current Count WorkGroupCurrentCount MAX Count WorkGroupMaxCountTable WorkGroupTable Entry WorkGroupEntry Number WorkGroupNumber Name WorkGroupNamePorts WorkGroupPorts Type WorkGroupTypeAppendix a Virtual Lans Vlans Vlans and Frame Tagging Vlan Vlan YELS10-27TX Vlan Configuration Vlan IDVlan Egress Vlan Access PortsPorts in Vlan Figure A-2. Vlan Access Ports Index NumericsSnmp Index