Enterasys Networks ELS10-27TX manual Configuring Vlans Using Snmp Overview, Config Table

Page 43

CHAPTER 3

CONFIGURING VLANS USING SNMP

3.1 OVERVIEW

This chapter describes how to create, delete or modify VLANs on the SmartSTACK Ethernet ELS10-27TX using SNMP. This chapter describes the procedure for using the following VLAN Configuration MIBs:

•The Config Table

•The Config Egress List

•802.1Q Mode

•The Filter GVRP table

•The Static MAC table

This chapter should be used in conjunction with Chapter 4, VLAN MIB Objects, in this manual.

3.2 THE CONFIG TABLE

The SmartSTACK Ethernet ELS10-27TX is capable of supporting 32 VLANs. The index into the VLAN table is from 0 to 31. The present table entries can be read, but not written, by setting the index to a value of 0 - 31. When configuring an entry, several values are used. These values are the VLAN ID, the ports on the VLAN, an IP address, an IP mask, and a VLAN name.

If the index is between 0 and 31, and one of these variables is read, the presently configured table entry will be returned.

To create, modify, or delete a VLAN entry, a multiple step process is required. The local variables must first be set with the values desired, followed by a command to process the variables. For a list of configuration MIBs, refer to Chapter 3, VLAN MIB Objects.

3-1

Image 43

Contents SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Vlan MIB Objects Configuring Vlans Using SnmpXiii Appendix a Virtual Lans Vlans Index Configuring Workgroups Using LCMConfiguring Workgroups Using Snmp Workgroup MIB ObjectsAbout this Supplement Your email address Getting HelpDocument Conventions Document Title Part Number Related DocumentationProduct Overview Using Vlans on the ELS10-27TXIeee 802.1Q Standard Vlan Hybrid Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Access Ports 802.1Q Mode Preserving Priority 3 802.1Q Trunk PortsNon-Preserving Priority Accessing Network Management Using VLANsDefault Port Vlan ID Switch ModeAssigning Ports to a Vlan Enable Gvrp Restricting VLANs 802.1Q ModeWorkgroups Virtual Workgroups will only operate in 802.1D modeInstallation and Management Default GatewayPage LCM Conventions OverviewSubset of LCM Commands LCM Command SummaryLCM Command Syntax Exit or Logout Basic LCM CommandsHelp EraseEnable Command Address Limit LCM CommandsRoute Command Port Command Port CommandEnhancements to LCM Commands Switch Command Trap Control Command ELS10-27vlan add 5-9 blue Vlan CommandPage Config Table Configuring Vlans Using Snmp OverviewStep Action Modifying, Creating and Deleting VLANsModifying a Vlan Deleting a Vlan Creating a VlanConfig Egress List Modifying a Config Egress List Entry Modifying, Creating or Deleting a Filter Gvrp Table Entry Filter Gvrp TableDeleting a Filter Creating a FilterCreating a Static MAC Entry Static MAC EntryDeleting a Static MAC Entry Vlan Version Number Bridge ConfigurationReset VlanReset Operating Mode VlanOperatingModeSyntax Octet String Size Gvrp Enable VlanGVRPEnableVlan VlanConfigVlan Access List VlanAccessListEntry VlanConfigEntry Configuration EntriesVlanConfigEntry VID VlanConfigVID Index VlanConfigIndexIP VlanConfigIP Ports VlanConfigPortsName VlanConfigName IP Mask VlanConfigIPMaskEstablish VlanConfigEstablish Status VlanConfigStatusDevice Entries Static Configured VlanNumConfiguredEntriesActive VlanNumActiveEntries Maximum Number VlanMaxNumEntries Configuration Table VlanConfigTableEgress Entry VlanConfigEgressEntry Egress Table Egress Table VlanConfigEgressTableIndex VlanEgressIndex VlanConfigEgressEntryList VlanEgressList VID VlanEgressVIDStatus VlanEgressStatus Gvrp VlanFilterGVRPTable Filter GvrpEntry VlanFilterGVRPEntry VlanFilterGVRPEntry VlanFilterGVRPIndexList VlanFilterGVRPList VID VlanFilterGVRPVIDEstablishVID VlanFilterGVRPEstablishVID Status VlanFilterGVRPStatusTable VlanStaticTable Static MAC Address EntriesEntry VlanStaticEntry VlanStaticEntry VID VlanStaticVIDPort VlanStaticPort MAC VlanStaticMACEstablish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Default Workgroup Configuration ExamplesWorkgroup Superset Workgroups are only valid in 802.1D mode LCM Workgroup CommandsELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Chapter Workgroup MIB Objects Overview Workgroups Using SnmpNext Number WorkGroupNextNumber MAX Count WorkGroupMaxCount Current Count WorkGroupCurrentCountTable WorkGroupTable Entry WorkGroupEntry Name WorkGroupName Number WorkGroupNumberType WorkGroupType Ports WorkGroupPortsVlan Vlan Y Appendix a Virtual Lans Vlans Vlans and Frame TaggingVlan ID ELS10-27TX Vlan ConfigurationPorts in Vlan Vlan Access PortsVlan Egress Figure A-2. Vlan Access Ports Numerics IndexSnmp Index