Enterasys Networks ELS10-27TX manual Chapter Workgroup MIB Objects Overview, Workgroups Using Snmp

Page 85

CHAPTER 7

WORKGROUP MIB OBJECTS

7.1 OVERVIEW

You can use a Cabletron Systems Network Management System (NMS), or a standard SNMP-based Network Management System, to manage the SmartSTACK Ethernet ELS10-27TX. This section describes Workgroup configuration using the Simple Network Management Protocol (SNMP).

You should have a familiarity with networking concepts and principles. In addition, a basic understanding of SNMP is helpful. SNMP Configuration information is shown on the following pages.

7.2 WORKGROUPS USING SNMP

The ELS10-27TX has support for the following OBJECT-IDENTIFIERs in the enterprise specific area. There are three Read-Only Workgroup variables, and four Read/Write Workgroup Table variables.

7.2.1 Next Number (WorkGroupNextNumber)

The next available workgroup number to be used. When creating a new workgroup, it is recommended to read the value of the variable and use it to key into the workgroup table.

els10-27WorkGroupNextNumber OBJECT-TYPE

SYNTAX INTEGER STRING (SIZE (1..8))

ACCESS read-only

STATUS mandatory

::= { els10-27WorkGroup 1 }

The MIB OBJECT IDENTIFIER for reading the VLANVersionNumber is:

OID 1.3.6.1.4.1.97.9.14.1

7-1

Image 85

Contents SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Vlan MIB Objects Configuring Vlans Using SnmpXiii Configuring Workgroups Using Snmp Configuring Workgroups Using LCMWorkgroup MIB Objects Appendix a Virtual Lans Vlans IndexAbout this Supplement Your email address Getting HelpDocument Conventions Document Title Part Number Related DocumentationProduct Overview Using Vlans on the ELS10-27TXIeee 802.1Q Standard Vlan Hybrid Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Access Ports 802.1Q Mode Preserving Priority 3 802.1Q Trunk PortsNon-Preserving Priority Accessing Network Management Using VLANsDefault Port Vlan ID Switch ModeAssigning Ports to a Vlan Enable Gvrp Restricting VLANs 802.1Q ModeWorkgroups Virtual Workgroups will only operate in 802.1D modeInstallation and Management Default GatewayPage LCM Conventions OverviewSubset of LCM Commands LCM Command SummaryLCM Command Syntax Help Basic LCM CommandsErase Exit or LogoutEnable Command Address Limit LCM CommandsRoute Command Port Command Port CommandEnhancements to LCM Commands Switch Command Trap Control Command ELS10-27vlan add 5-9 blue Vlan CommandPage Config Table Configuring Vlans Using Snmp OverviewStep Action Modifying, Creating and Deleting VLANsModifying a Vlan Deleting a Vlan Creating a VlanConfig Egress List Modifying a Config Egress List Entry Modifying, Creating or Deleting a Filter Gvrp Table Entry Filter Gvrp TableDeleting a Filter Creating a FilterCreating a Static MAC Entry Static MAC EntryDeleting a Static MAC Entry Vlan Version Number Bridge ConfigurationReset VlanReset Operating Mode VlanOperatingModeSyntax Octet String Size Gvrp Enable VlanGVRPEnableVlan VlanConfigVlan Access List VlanAccessListEntry VlanConfigEntry Configuration EntriesVlanConfigEntry VID VlanConfigVID Index VlanConfigIndexIP VlanConfigIP Ports VlanConfigPortsName VlanConfigName IP Mask VlanConfigIPMaskEstablish VlanConfigEstablish Status VlanConfigStatusDevice Entries Static Configured VlanNumConfiguredEntriesActive VlanNumActiveEntries Maximum Number VlanMaxNumEntries Configuration Table VlanConfigTableEgress Entry VlanConfigEgressEntry Egress Table Egress Table VlanConfigEgressTableIndex VlanEgressIndex VlanConfigEgressEntryList VlanEgressList VID VlanEgressVIDStatus VlanEgressStatus Gvrp VlanFilterGVRPTable Filter GvrpEntry VlanFilterGVRPEntry VlanFilterGVRPEntry VlanFilterGVRPIndexList VlanFilterGVRPList VID VlanFilterGVRPVIDEstablishVID VlanFilterGVRPEstablishVID Status VlanFilterGVRPStatusTable VlanStaticTable Static MAC Address EntriesEntry VlanStaticEntry VlanStaticEntry VID VlanStaticVIDPort VlanStaticPort MAC VlanStaticMACEstablish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Default Workgroup Configuration ExamplesWorkgroup Superset Workgroups are only valid in 802.1D mode LCM Workgroup CommandsELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Chapter Workgroup MIB Objects Overview Workgroups Using SnmpNext Number WorkGroupNextNumber MAX Count WorkGroupMaxCount Current Count WorkGroupCurrentCountTable WorkGroupTable Entry WorkGroupEntry Name WorkGroupName Number WorkGroupNumberType WorkGroupType Ports WorkGroupPortsVlan Vlan Y Appendix a Virtual Lans Vlans Vlans and Frame TaggingVlan ID ELS10-27TX Vlan ConfigurationPorts in Vlan Vlan Access PortsVlan Egress Figure A-2. Vlan Access Ports Numerics IndexSnmp Index