Enterasys Networks ELS10-27TX manual Modifying a Config Egress List Entry, Step Action

Page 47

Configuring VLANs Using SNMP

3.3.1 Modifying a Config Egress List Entry

To modify a Config Egress List entry, proceed as follows:

Step	Action


1	Set the index outside its valid range.

2	Set the VLAN ID to the value desired.

3	Set the port variable to the value desired.

4	Set the index to the table entry you desire to modify.

5	Write any value to the status variable.

When the write to the status entry is completed, an attempt will be made to carry out the command.

If modifying an existing entry in the table, the VLAN ID in the table entry must match the local variable. If it does not the command will be aborted.

If the VLAN ID is already in use, the index must also match. If it does not the command will be aborted.

The command will abort, if the VLAN ID is not valid, if the VLAN does not exist, or all ports are not members of that VLAN.

After all checks pass, the VLAN ID is copied to the default table based on the index specified. The ports selected are added to the existing list of ports in the table entry.

If the switch is operating in 802.1Q mode, the following will be performed by the firmware:

•Inform the hardware of the new PVID for the port(s).

•Delete the old default VLAN ID for these ports (PVID/MAC address pair).

•Add the new MAC address pair for these ports (PVID/MAC address pair).

•Delete all learned addresses for this VLAN.

•Flush all ARP entries.

3-5

Image 47

Contents SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Vlan MIB Objects Configuring Vlans Using SnmpXiii Appendix a Virtual Lans Vlans Index Configuring Workgroups Using LCMConfiguring Workgroups Using Snmp Workgroup MIB ObjectsAbout this Supplement Your email address Getting HelpDocument Conventions Document Title Part Number Related DocumentationProduct Overview Using Vlans on the ELS10-27TXIeee 802.1Q Standard Vlan Access Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Hybrid Ports 802.1Q Mode Preserving Priority 3 802.1Q Trunk PortsNon-Preserving Priority Accessing Network Management Using VLANsAssigning Ports to a Vlan Switch ModeDefault Port Vlan ID Enable Gvrp Restricting VLANs 802.1Q ModeWorkgroups Virtual Workgroups will only operate in 802.1D modeInstallation and Management Default GatewayPage LCM Conventions OverviewSubset of LCM Commands LCM Command SummaryLCM Command Syntax Exit or Logout Basic LCM CommandsHelp EraseEnable Command Address Limit LCM CommandsRoute Command Port Command Port CommandEnhancements to LCM Commands Switch Command Trap Control Command ELS10-27vlan add 5-9 blue Vlan CommandPage Config Table Configuring Vlans Using Snmp OverviewModifying a Vlan Modifying, Creating and Deleting VLANsStep Action Deleting a Vlan Creating a VlanConfig Egress List Modifying a Config Egress List Entry Modifying, Creating or Deleting a Filter Gvrp Table Entry Filter Gvrp TableDeleting a Filter Creating a FilterDeleting a Static MAC Entry Static MAC EntryCreating a Static MAC Entry Vlan Version Number Bridge ConfigurationReset VlanReset Operating Mode VlanOperatingModeSyntax Octet String Size Gvrp Enable VlanGVRPEnableVlan VlanConfigVlan Access List VlanAccessListVlanConfigEntry Configuration EntriesEntry VlanConfigEntry VID VlanConfigVID Index VlanConfigIndexIP VlanConfigIP Ports VlanConfigPortsName VlanConfigName IP Mask VlanConfigIPMaskEstablish VlanConfigEstablish Status VlanConfigStatusActive VlanNumActiveEntries Static Configured VlanNumConfiguredEntriesDevice Entries Maximum Number VlanMaxNumEntries Configuration Table VlanConfigTableEgress Entry VlanConfigEgressEntry Egress Table Egress Table VlanConfigEgressTableIndex VlanEgressIndex VlanConfigEgressEntryList VlanEgressList VID VlanEgressVIDStatus VlanEgressStatus Entry VlanFilterGVRPEntry Filter GvrpGvrp VlanFilterGVRPTable VlanFilterGVRPEntry VlanFilterGVRPIndexList VlanFilterGVRPList VID VlanFilterGVRPVIDEstablishVID VlanFilterGVRPEstablishVID Status VlanFilterGVRPStatusEntry VlanStaticEntry Static MAC Address EntriesTable VlanStaticTable VlanStaticEntry VID VlanStaticVIDPort VlanStaticPort MAC VlanStaticMACEstablish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Default Workgroup Configuration ExamplesWorkgroup Superset Workgroups are only valid in 802.1D mode LCM Workgroup CommandsELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Next Number WorkGroupNextNumber Workgroups Using SnmpChapter Workgroup MIB Objects Overview MAX Count WorkGroupMaxCount Current Count WorkGroupCurrentCountTable WorkGroupTable Entry WorkGroupEntry Name WorkGroupName Number WorkGroupNumberType WorkGroupType Ports WorkGroupPortsVlan Vlan Y Appendix a Virtual Lans Vlans Vlans and Frame TaggingVlan ID ELS10-27TX Vlan ConfigurationVlan Egress Vlan Access PortsPorts in Vlan Figure A-2. Vlan Access Ports Numerics IndexSnmp Index