Enterasys Networks ELS10-27TX manual Config Egress List

Page 46

Configuring VLANs Using SNMP

-The selected ports are removed from the list of ports in the table entry.

-If there are no ports left on the VLAN, and the VLAN ID does not equal 0x001, then the BPDU addresses and the MP MAC address is deleted from the address database.

-All APR entries are flushed from the ARP table.

-If there are no ports left on the VLAN, delete the IP address from the routing table and clear the table entry.

3.3THE CONFIG EGRESS LIST

The ConfigEgressList table is used to configure the default VLAN ID on specific ports. This is always a modify function, therefore, there is no need for the VlanConfigEstablish object.

The four parameters are index, VLAN ID, ports and status. For a list of Config Egress MIB, refer to Chapter 3, Configuring VLANs Using SNMP.

As in the config table, valid entries are between 0 and 31. An index outside of this range allows read/write access to the local variables.

You must do a read of the entire table to gain knowledge of current table configuration.

3-4

Image 46
Contents SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Configuring Vlans Using Snmp Vlan MIB ObjectsXiii Workgroup MIB Objects Configuring Workgroups Using LCMConfiguring Workgroups Using Snmp Appendix a Virtual Lans Vlans IndexAbout this Supplement Getting Help Your email addressDocument Conventions Related Documentation Document Title Part NumberUsing Vlans on the ELS10-27TX Product OverviewIeee 802.1Q Standard Vlan Hybrid Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Access Ports 802.1Q Mode 3 802.1Q Trunk Ports Preserving PriorityAccessing Network Management Using VLANs Non-Preserving PriorityDefault Port Vlan ID Switch ModeAssigning Ports to a Vlan Restricting VLANs 802.1Q Mode Enable GvrpVirtual Workgroups will only operate in 802.1D mode WorkgroupsDefault Gateway Installation and ManagementPage Overview LCM ConventionsLCM Command Summary Subset of LCM CommandsLCM Command Syntax Erase Basic LCM CommandsHelp Exit or LogoutLCM Commands Enable Command Address LimitRoute Command Port Command Port CommandEnhancements to LCM Commands Switch Command Trap Control Command Vlan Command ELS10-27vlan add 5-9 bluePage Configuring Vlans Using Snmp Overview Config TableStep Action Modifying, Creating and Deleting VLANsModifying a Vlan Creating a Vlan Deleting a VlanConfig Egress List Modifying a Config Egress List Entry Filter Gvrp Table Modifying, Creating or Deleting a Filter Gvrp Table EntryCreating a Filter Deleting a FilterCreating a Static MAC Entry Static MAC EntryDeleting a Static MAC Entry Bridge Configuration Vlan Version NumberOperating Mode VlanOperatingMode Reset VlanResetGvrp Enable VlanGVRPEnable Syntax Octet String SizeAccess List VlanAccessList Vlan VlanConfigVlanEntry VlanConfigEntry Configuration EntriesVlanConfigEntry Index VlanConfigIndex VID VlanConfigVIDPorts VlanConfigPorts IP VlanConfigIPIP Mask VlanConfigIPMask Name VlanConfigNameStatus VlanConfigStatus Establish VlanConfigEstablishDevice Entries Static Configured VlanNumConfiguredEntriesActive VlanNumActiveEntries Configuration Table VlanConfigTable Maximum Number VlanMaxNumEntriesEgress Table Egress Table VlanConfigEgressTable Egress Entry VlanConfigEgressEntryVlanConfigEgressEntry Index VlanEgressIndexVID VlanEgressVID List VlanEgressListStatus VlanEgressStatus Gvrp VlanFilterGVRPTable Filter GvrpEntry VlanFilterGVRPEntry VlanFilterGVRPIndex VlanFilterGVRPEntryVID VlanFilterGVRPVID List VlanFilterGVRPListStatus VlanFilterGVRPStatus EstablishVID VlanFilterGVRPEstablishVIDTable VlanStaticTable Static MAC Address EntriesEntry VlanStaticEntry VID VlanStaticVID VlanStaticEntryMAC VlanStaticMAC Port VlanStaticPortEstablish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Configuration Examples Workgroup DefaultWorkgroup Superset LCM Workgroup Commands Workgroups are only valid in 802.1D modeELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Chapter Workgroup MIB Objects Overview Workgroups Using SnmpNext Number WorkGroupNextNumber Current Count WorkGroupCurrentCount MAX Count WorkGroupMaxCountTable WorkGroupTable Entry WorkGroupEntry Number WorkGroupNumber Name WorkGroupNamePorts WorkGroupPorts Type WorkGroupTypeAppendix a Virtual Lans Vlans Vlans and Frame Tagging Vlan Vlan YELS10-27TX Vlan Configuration Vlan IDPorts in Vlan Vlan Access PortsVlan Egress Figure A-2. Vlan Access Ports Index NumericsSnmp Index