Enterasys Networks 2H252-25R manual Removing the Chassis Cover

Page 54

Removing the Chassis Cover

B.2 REMOVING THE CHASSIS COVER

This section describes how to remove the 2H252-25R chassis cover.

DO NOT REMOVE THE COVER FROM THE 2H252-25R WHILE POWER IS APPLIED TO THE UNIT. HAZARDOUS VOLTAGES ARE PRESENT AND COULD CAUSE PERSONAL INJURY AND/OR DAMAGE THE UNIT.

DO NOT POWER UP THE 2H252-25R AGAIN UNTIL THE COVER AND SCREWS ARE IN PLACE.

DECKEL VON DAS 2H252-25R NICHT ABZIEHEN UNTER SPANNUNG. GEFAHR FÜR DAS PERSONNAL UND/ODER DAS GERÄT WEGEN GEFÄHRLICHE SPANNUNGEN ENSTEHT.

2H252-25R NICHEINSCHALTEN SO LANG DER DECKEL UND SCHRAUBEN NICHT EINGEBAUT SIND.

NO DEBE DE REMOVER LA TAPA DURENTE QUE ESTE CONELTADO A LA CORRIENTE, UNA DESCARGA ELECTRICA LE PUEDE CAUSAR Y PROBOCARLE DAÑOS, AL IGUAL QUE AL APARATO.

NO ENCHUFE A LA CORRIENTE HASTA QUE LA TAPA Y LOS TORNILLOS ESTEN EN SU LUGAR.

CAUTION: THIS UNIT MAY HAVE MORE THAN ONE POWER SUPPLY CORD. DISCONNECT TWO POWER SUPPLY CORDS BEFORE SERVICING TO AVOID ELECTRIC SHOCK.

VORSICHT: DIESES GERÄT HAT MEHR ALS EINEN NETZANSCHLUß. TRENNEN SIE VOR WARTUNGSARBEITEN DIE 2 NET ZANSCHLÜSSE VOM NETZ, UM ELEKTRISCHE SCHLÄGE ZU VERMEIDEN.

ATTENTION: CET APPAREIL COMPORTE PLUS D’UN CORDON D’ALIMENTATION. RAFIN DE PREVENIR LES CHOCS ELECTRIQUES, DEGRANCHER LES DEUX CORDONS D’ALIMENTATION AVANT DE FAIRE LE DEPANNAGE.

B-2Optional Installations and Mode Switch Bank Settings

Image 54
Contents 2H252-25R SmartSwitch Installation User’s Guide Page Page Vcci Notice FCC NoticeIndustry Canada Notice Class a ITE NoticeEnterasys NETWORKS, INC Program License Agreement Page Declaration of Conformity Page Contents Troubleshooting Figures Tables Using this Guide About This GuideStructure of this Guide Related Documents Document Conventions Guide uses the following conventionsPage Introduction OverviewConnectivity Runtime IP Address DiscoveryFull Duplex Switched Ethernet SmartTrunkPort/VLAN Redirect Functions Remote Monitoring RmonBroadcast Suppression Rate LimitingGarp Switch Operation Flow ControlManagement Switching Options11 802.1 Port Priority Optional HSIMs and VHSIMsLanview Diagnostic LEDs Standards CompatibilityYear 2000 Compliant Getting Help Your email addressNetwork Requirements 10BASE-T Network100BASE-TX Network Installation Unpacking the DeviceInstalling Options Guidelines for Tabletop and Shelf Installations Installing the DeviceTabletop or Shelf Installation InstallationRackmount Installation Guidelines for the Rackmount InstallationAttaching the Strain-Relief Bracket Rack Mounting the 2H252-25R Strain-Relief Bracket ScrewsRackmount Bracket Screws Connecting Power Redundant Primary AC outlets are On separate circuitsConnecting to the Network Connecting Twisted Pair Cables to Fixed PortsConnecting the Twisted Pair Segment Straight-Through Cable Completing the Installation Troubleshooting Using LanviewLanview LEDs PWR CPU FDX Troubleshooting Checklist Local Management User’s Guide2E253, 2H252, 2H253 SmartSwitch Series 2E253 Using the Reset Button Reset ButtonPage Specifications Device SpecificationsPhysical Properties Electrical Specifications Environmental RequirementsINPUT/OUTPUT Ports COM Port Pinout Assignments Regulatory CompliancePage Optional Installations Mode Switch Bank Settings Required ToolsRemoving the Chassis Cover Optional Installations and Mode Switch Bank Settings B-3 Screws Chassis Cover Front Panel Setting the Mode Switches Figure B-2 Mode Switch Location6Optional Installations and Mode Switch Bank Settings Simm Upgrade Locating SIMMsInstalling the Dram Simm Installing Optional Hsim or Vhsim Interface Modules Figure B-5 Hsim and Vhsim Connector LocationsPage Index NumericsIndex-2