Cypress CY7C1393BV18 manual Features, Configurations, Functional Description, Selection Guide

CY7C1392BV18, CY7C1992BV18 CY7C1393BV18, CY7C1394BV18

18-Mbit DDR-II SIO SRAM 2-Word Burst Architecture

Features

■18-Mbit density (2M x 8, 2M x 9, 1M x 18, 512K x 36)

■300 MHz clock for high bandwidth

■2-word burst for reducing address bus frequency

■Double Data Rate (DDR) interfaces

(data transferred at 600 MHz) at 300 MHz

■Two input clocks (K and K) for precise DDR timing ❐ SRAM uses rising edges only

■Two input clocks for output data (C and C) to minimize clock skew and flight time mismatches

■Echo clocks (CQ and CQ) simplify data capture in high-speed systems

■Synchronous internally self-timed writes

■1.8V core power supply with HSTL inputs and outputs

■Variable drive HSTL output buffers

■Expanded HSTL output voltage (1.4V–VDD)

■Available in 165-Ball FBGA package (13 x 15 x 1.4 mm)

■Offered in both Pb-free and non Pb-free packages

■JTAG 1149.1 compatible test access port

■Delay Lock Loop (DLL) for accurate data placement

Configurations

CY7C1392BV18 – 2M x 8

CY7C1992BV18 – 2M x 9

CY7C1393BV18 – 1M x 18

CY7C1394BV18 – 512K x 36

Functional Description

The CY7C1392BV18, CY7C1992BV18, CY7C1393BV18, and CY7C1394BV18 are 1.8V Synchronous Pipelined SRAMs, equipped with Double Data Rate Separate IO (DDR-II SIO) architecture. The DDR-II SIO consists of two separate ports: the read port and the write port to access the memory array. The read port has data outputs to support read operations and the write port has data inputs to support write operations. The DDR-II SIO has separate data inputs and data outputs to completely eliminate the need to “turn-around” the data bus required with common IO devices. Access to each port is accomplished through a common address bus. Addresses for read and write are latched on alternate rising edges of the input (K) clock. Write data is registered on the rising edges of both K and K. Read data is driven on the rising edges of C and C if provided, or on the rising edge of K and K if C/C are not provided. Each address location is associated with two 8-bit words in the case of CY7C1392BV18, two 9-bit words in the case of CY7C1992BV18, two 18-bit words in the case of CY7C1393BV18, and two 36-bit words in the case of CY7C1394BV18 that burst sequentially into or out of the device.

Asynchronous inputs include an output impedance matching input (ZQ). Synchronous data outputs are tightly matched to the two output echo clocks CQ/CQ, eliminating the need to capture data separately from each individual DDR-II SIO SRAM in the system design. Output data clocks (C/C) enable maximum system clocking and data synchronization flexibility.

All synchronous inputs pass through input registers controlled by the K or K input clocks. All data outputs pass through output registers controlled by the C or C (or K or K in a single clock domain) input clocks. Writes are conducted with on-chip synchronous self-timed write circuitry.

Selection Guide

Description		300 MHz	278 MHz	250 MHz	200 MHz	167 MHz	Unit
Maximum Operating Frequency		300	278	250	200	167	MHz
Maximum Operating Current	x8	820	770	700	575	485	mA
	x9	825	775	700	575	490
	x18	865	800	725	600	500
	x36	935	850	770	630	540

Cypress Semiconductor Corporation • 198 Champion Court	•	San Jose, CA 95134-1709	•	408-943-2600
Document #: 38-05623 Rev. *D			Revised June 2, 2008

[+] Feedback