Avaya P580 Enabling Option 82 for Dhcp, Changing the Status of Option 82 by Using the Web Agent

Page 12

Removing Port Mirroring

Viewing Information about Port Mirroring

To use the Web Agent to remove port mirroring:

1.Expand the Modules & Ports folder.

2.Click Port Mirroring.

The Port Mirroring Information page opens.

3.In the Source Port column, select None for the port mirror that you want to remove.

4.Click Apply.

To use the Web Agent to view information about port mirroring:

1.Expand the Modules & Ports folder.

2.Click Port Mirroring.

The Port Mirroring Information page opens. This page displays information about all port mirrors that are setup.

Enabling Option 82 for DHCP

Option 82 for DHCP includes two suboptions:

Suboption 1 identifies the slot and physical port number from which the DHCP request was received.

Suboption 2 identifies the IP address and, if available, the system name of the switch.

By default, both of these suboptions are enabled. You can change the status of either or both suboptions by using the Web Agent, Command Line Interface (CLI), or SNMP.

Changing the Status of Option 82 by Using the Web Agent

To use the Web Agent to change the status of option 82:

1.Open the IP Global Configuration page.

For information on how to open this page, see “Enabling IP Routing” in chapter 9 of Cajun P550R/P880/P882 Switch User Guide Version, v5.0.

12

June 14, 2001

610-0184-095

Image 12
Contents Cajun P550R/P580/P880/P882 Switch Release Notes OverviewNew Hardware and Software Features Software FeaturesHardware June 14 Supported Product Binaries and Boot Codes Queue Classification and Servicing FeaturesType of Switch Binary File Boot File OverviewClassification of Traffic Port Mirroring on 80-Series Modules WFQ Queue-Servicing AlgorithmConfiguring Port Mirroring By Using the CLI Setting Up Port MirroringPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel Configuring Port Mirroring By Using the Web Agent If you select ThenChanging the Status of Option 82 by Using the Web Agent Enabling Option 82 for DhcpChanging the Status of Option 82 by Using the CLI Changing the Status of Option 82 by Using SnmpMIB Item Cjnipv4serv.mibEnabling MAC Address Lock and Traps by Using the Web Agent Enabling MAC Address Lock and Traps by Using the CLIEnabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt, versionMIB, MIB Items, and OIDs for MAC Address Lock ProminetMib.txtChanged CLI Commands Corrected ProblemsEnhancements Known Problems and Workarounds Command Line Interface CLIATM Uplink Modules Flood Rate LimitingFrames Transmitted with Cyclic Redundancy Check CRC Errors Desired Rate Web or CLI SettingHot Swap Modules Igmp Group Membership TableIntelligent Multicasting Example IPX L3 Forwarding CacheOption 82 for Dchp Point-to-Point Protocol PPP and TelnetPort Mirroring Series ModulesRedundant Switch Controller Remote Monitoring RmonSimple Network-Management Protocol Snmp Downloading the Startup Configuration File P580/P882 Chassis SlotSupervisor Module Switch Ports Following error message in the CLIVlan Issues Web AFT IssuesFunctional Restrictions Auto-NegotiationChecksum Error Message CajunViewCPU Synchronization Legacy CLIDistance Vector Multicast Routing Protocol Dvmrp Hunt GroupsLink Status Loopback Tests NetscapeOversized Packets Redundant Controller Support Software License KeyingSpanning Tree Protocol STP 3Com TaggingDocumentation Updates and Corrections Tftp Download Status DelayCajun P550R/P880/P882 Switch User Guide Web AgentTechnical Support Click InterfacesSetting the Priority of a Port CommandSetting a Port to Ignore Tag Priority ExamplesDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings