Avaya P550R, P580, P880 manual Displaying the Queue Service Settings

Page 43

To assign a weight of 5 to queue 4, enter:

>queue 4 weight 5

To assign a weight of 6 to queue 5, enter:

>queue 5 weight 6

To assign a weight of 7 to queue 6, enter:

>queue 6 weight 7

To assign a weight of 8 to queue 7, enter:

>queue 7 weight 8

Displaying the Queue Service Settings

Command

Use the show queue-servicecommand to display the settings for queue service. The correct syntax for this command is:

>show queue-service {<slot><mod-port-range>} [...,{<slot><mod-port-range>}]

where

<slot> is a slot number

<mod-port-range> is 0-7

If you specify this parameter, then the settings for all of the ports on the module in slot <slot> are displayed.

<slot-swport-range>is a slot and port range in the form of 3/1 or 3/1-5. If you specify this parameter, then the queue service settings for ports <swport-range>on the module in slot <slot> are displayed.

Examples

To display the queue service settings for port 1 on the module in slot 3, enter:

> show queue-service 3/1

610-0184-095

June 14, 2001

A-9

Image 43
Contents Overview Cajun P550R/P580/P880/P882 Switch Release NotesSoftware Features New Hardware and Software FeaturesHardware June 14 Overview Supported Product Binaries and Boot CodesQueue Classification and Servicing Features Type of Switch Binary File Boot FileClassification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series ModulesSetting Up Port Mirroring Configuring Port Mirroring By Using the CLIPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel If you select Then Configuring Port Mirroring By Using the Web AgentEnabling Option 82 for Dhcp Changing the Status of Option 82 by Using the Web AgentCjnipv4serv.mib Changing the Status of Option 82 by Using the CLIChanging the Status of Option 82 by Using Snmp MIB ItemEnabling MAC Address Lock and Traps by Using the CLI Enabling MAC Address Lock and Traps by Using the Web AgentEnabling Traps for Unknown Source Addresses ProminetMib.txt, version Enabling MAC Address Lock and Traps by Using SnmpProminetMib.txt MIB, MIB Items, and OIDs for MAC Address LockCorrected Problems Changed CLI CommandsEnhancements Flood Rate Limiting Known Problems and WorkaroundsCommand Line Interface CLI ATM Uplink ModulesDesired Rate Web or CLI Setting Frames Transmitted with Cyclic Redundancy Check CRC ErrorsIgmp Group Membership Table Hot Swap ModulesIntelligent Multicasting Example L3 Forwarding Cache IPXPoint-to-Point Protocol PPP and Telnet Option 82 for DchpSeries Modules Port MirroringRemote Monitoring Rmon Redundant Switch ControllerSimple Network-Management Protocol Snmp P580/P882 Chassis Slot Downloading the Startup Configuration FileSupervisor Module Following error message in the CLI Switch PortsAuto-Negotiation Vlan IssuesWeb AFT Issues Functional RestrictionsLegacy CLI Checksum Error MessageCajunView CPU SynchronizationHunt Groups Distance Vector Multicast Routing Protocol DvmrpLink Status Netscape Loopback TestsOversized Packets 3Com Tagging Redundant Controller SupportSoftware License Keying Spanning Tree Protocol STPWeb Agent Documentation Updates and CorrectionsTftp Download Status Delay Cajun P550R/P880/P882 Switch User GuideClick Interfaces Technical SupportCommand Setting the Priority of a PortExamples Setting a Port to Ignore Tag PriorityDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings