Avaya P550R, P580, P880 manual Redundant Switch Controller, Remote Monitoring Rmon

Page 25

If a router port for intelligent multicasting is mirrored with a piggyback port, the piggyback port is listed instead of the router port.

Redundant Switch Controller

The following problem has no workaround:

Do not enable redundancy unless you have a redundant switch controller.

On a P880 with an 80-series supervisor module, the redundant switch controller may not take over when the active switch controller fails.

Remote Monitoring (RMON)

The following problems have no workaround:

30 minute RMON statistics always show utilization as 0 (Zero) on a heavily used Gigabit Ethernet port.

Statistics for unicast frames do not work when using multilayer (ISL) tagging.

Simple Network-Management Protocol (SNMP)

 

The following problems have no workaround:

 

Cold start traps cannot be transmitted out of inband

 

interfaces after you enable Spanning Tree.

 

ipAddrTable does not display inactive interfaces (VLANs). An

 

inactive interface occurs when there are no active ports on a

 

VLAN.

Problem:

If you use the CLI to perform either of the following

 

commands, the supervisor module stops responding and

 

resets:

 

snmp walk aarpNetAddress

 

snmp walk cjnAtEchoSend

Workaround:

Use SNMP from a management station to access these MIB items.

610-0184-095

June 14, 2001

25

Image 25
Contents Overview Cajun P550R/P580/P880/P882 Switch Release NotesSoftware Features New Hardware and Software FeaturesHardware June 14 Queue Classification and Servicing Features Supported Product Binaries and Boot CodesType of Switch Binary File Boot File OverviewClassification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series ModulesSetting Up Port Mirroring Configuring Port Mirroring By Using the CLIPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel If you select Then Configuring Port Mirroring By Using the Web AgentEnabling Option 82 for Dhcp Changing the Status of Option 82 by Using the Web AgentChanging the Status of Option 82 by Using Snmp Changing the Status of Option 82 by Using the CLIMIB Item Cjnipv4serv.mibEnabling MAC Address Lock and Traps by Using the CLI Enabling MAC Address Lock and Traps by Using the Web AgentEnabling Traps for Unknown Source Addresses ProminetMib.txt, version Enabling MAC Address Lock and Traps by Using SnmpProminetMib.txt MIB, MIB Items, and OIDs for MAC Address LockCorrected Problems Changed CLI CommandsEnhancements Command Line Interface CLI Known Problems and WorkaroundsATM Uplink Modules Flood Rate LimitingDesired Rate Web or CLI Setting Frames Transmitted with Cyclic Redundancy Check CRC ErrorsIgmp Group Membership Table Hot Swap ModulesIntelligent Multicasting Example L3 Forwarding Cache IPXPoint-to-Point Protocol PPP and Telnet Option 82 for DchpSeries Modules Port MirroringRemote Monitoring Rmon Redundant Switch ControllerSimple Network-Management Protocol Snmp P580/P882 Chassis Slot Downloading the Startup Configuration FileSupervisor Module Following error message in the CLI Switch PortsWeb AFT Issues Vlan IssuesFunctional Restrictions Auto-NegotiationCajunView Checksum Error MessageCPU Synchronization Legacy CLIHunt Groups Distance Vector Multicast Routing Protocol DvmrpLink Status Netscape Loopback TestsOversized Packets Software License Keying Redundant Controller SupportSpanning Tree Protocol STP 3Com TaggingTftp Download Status Delay Documentation Updates and CorrectionsCajun P550R/P880/P882 Switch User Guide Web AgentClick Interfaces Technical SupportCommand Setting the Priority of a PortExamples Setting a Port to Ignore Tag PriorityDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings