Avaya P550R, P580, P880 manual Technical Support, Click Interfaces

Page 34

The steps in ”Modifying OSPF Interfaces” of chapter 11, “Configuring the OSPF Routing Protocol” should read as follows:

1.Administratively disable the interface on which you want to modify OSPF.

*Note: You must disable the interface to perform any OSPF modifications to the interface.

2.In the navigation pane of the Web Agent window, expand the Routing > IP > OSPF folders.

3.Click Interfaces.

The OSPF Interfaces page opens (Figure 11-4).

4.Modify the OSPF interface parameters. Refer to Table 11-3 for an explanation of these parameters.

5.Administratively enable the modified interface.

*Note: You must reenable the interface for the switch to accept the modifications.

Technical Support

To contact Avaya’s technical support:

*Note: These are new phone numbers as of October 1, 2000.

■From the United States: 1-800-237-0016

■From North America:

1-800-242-2121

■Outside North America: Contact your distributor

34

June 14, 2001

610-0184-095

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Cajun P550R/P580/P880/P882 Switch Release Notes OverviewSoftware Features New Hardware and Software FeaturesHardware June 14 Type of Switch Binary File Boot File Supported Product Binaries and Boot CodesQueue Classification and Servicing Features OverviewClassification of Traffic Port Mirroring on 80-Series Modules WFQ Queue-Servicing AlgorithmConfiguring Port Mirroring By Using the CLI Setting Up Port MirroringPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel Configuring Port Mirroring By Using the Web Agent If you select ThenChanging the Status of Option 82 by Using the Web Agent Enabling Option 82 for DhcpMIB Item Changing the Status of Option 82 by Using the CLIChanging the Status of Option 82 by Using Snmp Cjnipv4serv.mibEnabling MAC Address Lock and Traps by Using the CLI Enabling MAC Address Lock and Traps by Using the Web AgentEnabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt, versionMIB, MIB Items, and OIDs for MAC Address Lock ProminetMib.txtCorrected Problems Changed CLI CommandsEnhancements ATM Uplink Modules Known Problems and WorkaroundsCommand Line Interface CLI Flood Rate LimitingFrames Transmitted with Cyclic Redundancy Check CRC Errors Desired Rate Web or CLI SettingIgmp Group Membership Table Hot Swap ModulesIntelligent Multicasting Example IPX L3 Forwarding CacheOption 82 for Dchp Point-to-Point Protocol PPP and TelnetPort Mirroring Series ModulesRemote Monitoring Rmon Redundant Switch ControllerSimple Network-Management Protocol Snmp P580/P882 Chassis Slot Downloading the Startup Configuration FileSupervisor Module Switch Ports Following error message in the CLIFunctional Restrictions Vlan IssuesWeb AFT Issues Auto-NegotiationCPU Synchronization Checksum Error MessageCajunView Legacy CLIHunt Groups Distance Vector Multicast Routing Protocol DvmrpLink Status Netscape Loopback TestsOversized Packets Spanning Tree Protocol STP Redundant Controller SupportSoftware License Keying 3Com TaggingCajun P550R/P880/P882 Switch User Guide Documentation Updates and CorrectionsTftp Download Status Delay Web AgentTechnical Support Click InterfacesSetting the Priority of a Port CommandSetting a Port to Ignore Tag Priority ExamplesDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings
Top Page Image Contents