Avaya P880, P580, P550R manual Enhancements, Changed CLI Commands, Corrected Problems

Page 17

Enhancements

The following events are now logged in the event log:

■Saving the running configuration to the startup configuration

■Creating an IP interface

■Modifying an IP interface

■Deleting an IP interface

Changed CLI Commands

■The get Fabric_mode command replaces the get Cajun_mode command.

■The set Fabric_mode command replaces the set Cajun_mode command.

Corrected Problems

The following problems have been corrected in this release:

■Pulling the base port on a hunt group no longer causes traffic to lose duplexity and broadcast to all ports within the VLAN.

■The SNMP error message no longer displays when you perform a LOADMIB operation.

■You can now create a row in the GenAppFile table in the

LOAD MIB.

■A software modification has been implemented for the LEDS on the 24-port, 10/100 Ethernet module with RJ45 connectors. The LEDs no longer illuminate when nothing is connected to them.

■The switch no longer stops learning remote MAC addresses over the ATM link when 36 or more virtual switch ports (VSPs) are configured.

■When running AppleTalk Network Assistance, the switch no longer stops forwarding layer 3 traffic.

610-0184-095

June 14, 2001

17

Image 17

Contents Overview Cajun P550R/P580/P880/P882 Switch Release NotesHardware New Hardware and Software FeaturesSoftware Features June 14 Queue Classification and Servicing Features Supported Product Binaries and Boot CodesType of Switch Binary File Boot File OverviewClassification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series ModulesSetting Up Port Mirroring Configuring Port Mirroring By Using the CLIPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel If you select Then Configuring Port Mirroring By Using the Web AgentEnabling Option 82 for Dhcp Changing the Status of Option 82 by Using the Web AgentChanging the Status of Option 82 by Using Snmp Changing the Status of Option 82 by Using the CLIMIB Item Cjnipv4serv.mibEnabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using the Web AgentEnabling MAC Address Lock and Traps by Using the CLI ProminetMib.txt, version Enabling MAC Address Lock and Traps by Using SnmpProminetMib.txt MIB, MIB Items, and OIDs for MAC Address LockEnhancements Changed CLI CommandsCorrected Problems Command Line Interface CLI Known Problems and WorkaroundsATM Uplink Modules Flood Rate LimitingDesired Rate Web or CLI Setting Frames Transmitted with Cyclic Redundancy Check CRC ErrorsIntelligent Multicasting Hot Swap ModulesIgmp Group Membership Table Example L3 Forwarding Cache IPXPoint-to-Point Protocol PPP and Telnet Option 82 for DchpSeries Modules Port MirroringSimple Network-Management Protocol Snmp Redundant Switch ControllerRemote Monitoring Rmon Supervisor Module Downloading the Startup Configuration FileP580/P882 Chassis Slot Following error message in the CLI Switch PortsWeb AFT Issues Vlan IssuesFunctional Restrictions Auto-NegotiationCajunView Checksum Error MessageCPU Synchronization Legacy CLILink Status Distance Vector Multicast Routing Protocol DvmrpHunt Groups Oversized Packets Loopback TestsNetscape Software License Keying Redundant Controller SupportSpanning Tree Protocol STP 3Com TaggingTftp Download Status Delay Documentation Updates and CorrectionsCajun P550R/P880/P882 Switch User Guide Web AgentClick Interfaces Technical SupportCommand Setting the Priority of a PortExamples Setting a Port to Ignore Tag PriorityDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings