Avaya P580, P550R Known Problems and Workarounds, ATM Uplink Modules, Command Line Interface CLI

Page 18

Known Problems and Workarounds

The following known problems and workarounds apply to Cajun P550R, P580, P880, and P882 switches that are running switch software, v5.2.2. If a known problem has a viable workaround, it immediately follows the Problem statement. If the known problem has no viable workaround, it is listed as a bulleted statement.

ARP

Problem:50-Series and 80-Series modules lose ARPs after you perform an initialization of NVRAM (NVRAM init).

Workaround: Reboot the switch twice after performing an NVRAM init.

ATM Uplink Modules

The following problem has no workaround:

The 50-series ATM Uplink modules do not work in slot 16 or slot 17 if you are using an 80-Series Supervisor module in a Cajun P882 switch.

Command Line Interface (CLI)

The following problem has no workaround

The “!” character, when used as part of a CLI command, is considered a comment by the Cajun switch software:

If you type “!” BEFORE a CLI command, the switch ignores the command and returns you to the CLI prompt.

If you type “!” after a CLI command, the switch displays an Invalid Command or Syntax Error error message.

Flood Rate Limiting

Problem:The options for setting flood rate limiting on 80-series, 10/100 Ethernet modules and on 80-series, 100 Base-FX Ethernet modules are incorrect. The correct rates are not available from the Web Agent or CLI.

18

June 14, 2001

610-0184-095

Image 18
Contents Cajun P550R/P580/P880/P882 Switch Release Notes OverviewNew Hardware and Software Features Software FeaturesHardware June 14 Type of Switch Binary File Boot File Supported Product Binaries and Boot CodesQueue Classification and Servicing Features OverviewClassification of Traffic Port Mirroring on 80-Series Modules WFQ Queue-Servicing AlgorithmConfiguring Port Mirroring By Using the CLI Setting Up Port MirroringPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel Configuring Port Mirroring By Using the Web Agent If you select ThenChanging the Status of Option 82 by Using the Web Agent Enabling Option 82 for DhcpMIB Item Changing the Status of Option 82 by Using the CLIChanging the Status of Option 82 by Using Snmp Cjnipv4serv.mibEnabling MAC Address Lock and Traps by Using the Web Agent Enabling MAC Address Lock and Traps by Using the CLIEnabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt, versionMIB, MIB Items, and OIDs for MAC Address Lock ProminetMib.txtChanged CLI Commands Corrected ProblemsEnhancements ATM Uplink Modules Known Problems and WorkaroundsCommand Line Interface CLI Flood Rate LimitingFrames Transmitted with Cyclic Redundancy Check CRC Errors Desired Rate Web or CLI SettingHot Swap Modules Igmp Group Membership TableIntelligent Multicasting Example IPX L3 Forwarding CacheOption 82 for Dchp Point-to-Point Protocol PPP and TelnetPort Mirroring Series ModulesRedundant Switch Controller Remote Monitoring RmonSimple Network-Management Protocol Snmp Downloading the Startup Configuration File P580/P882 Chassis SlotSupervisor Module Switch Ports Following error message in the CLIFunctional Restrictions Vlan IssuesWeb AFT Issues Auto-NegotiationCPU Synchronization Checksum Error MessageCajunView Legacy CLIDistance Vector Multicast Routing Protocol Dvmrp Hunt GroupsLink Status Loopback Tests NetscapeOversized Packets Spanning Tree Protocol STP Redundant Controller SupportSoftware License Keying 3Com TaggingCajun P550R/P880/P882 Switch User Guide Documentation Updates and CorrectionsTftp Download Status Delay Web AgentTechnical Support Click InterfacesSetting the Priority of a Port CommandSetting a Port to Ignore Tag Priority ExamplesDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings