Avaya P880, P580, P550R manual Checksum Error Message, CajunView, CPU Synchronization, Legacy CLI

Page 29

Workaround: Either:

■Disable auto-negotiation

■Use a patch cable that is longer that 5 meters

■Enter the following Enhanced CLI command in legacy mode: > port set NationalPhyMode <slot>.<port> enable

The factory default for the National Phy Mode is Enable.

Checksum Error Message

Problem:	The following checksum error displays after you upgrade from 4.3.x
	code to v5.x code:
	Bad file header compressed checksum...transfer cancelled.
Workaround:	Ignore the checksum error and reboot the switch to upgrade the
	software.

CajunView v3.0

CajunView v3.0 does not support 80-series hardware. CajunView v4.0 will support 50-series hardware and 80-series hardware on Cajun switch software code version 5.1 and later.

CPU Synchronization

Problem:If you attempt to synchronize the active supervisor and redundant supervisor while the supervisor is being heavily used, TFTP transfers from the active supervisor to the redundant supervisor may time out and fail.

Workaround: Repeat the synchronization when use of the supervisor has decreased.

Legacy CLI

Problem:The Legacy CLI setup command does not save information that you enter.

610-0184-095

June 14, 2001

29

Image 29

Contents Overview Cajun P550R/P580/P880/P882 Switch Release NotesHardware New Hardware and Software FeaturesSoftware Features June 14 Queue Classification and Servicing Features Supported Product Binaries and Boot CodesType of Switch Binary File Boot File OverviewClassification of Traffic WFQ Queue-Servicing Algorithm Port Mirroring on 80-Series ModulesSetting Up Port Mirroring Configuring Port Mirroring By Using the CLIPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel If you select Then Configuring Port Mirroring By Using the Web AgentEnabling Option 82 for Dhcp Changing the Status of Option 82 by Using the Web AgentChanging the Status of Option 82 by Using Snmp Changing the Status of Option 82 by Using the CLIMIB Item Cjnipv4serv.mibEnabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using the Web AgentEnabling MAC Address Lock and Traps by Using the CLI ProminetMib.txt, version Enabling MAC Address Lock and Traps by Using SnmpProminetMib.txt MIB, MIB Items, and OIDs for MAC Address LockEnhancements Changed CLI CommandsCorrected Problems Command Line Interface CLI Known Problems and WorkaroundsATM Uplink Modules Flood Rate LimitingDesired Rate Web or CLI Setting Frames Transmitted with Cyclic Redundancy Check CRC ErrorsIntelligent Multicasting Hot Swap ModulesIgmp Group Membership Table Example L3 Forwarding Cache IPXPoint-to-Point Protocol PPP and Telnet Option 82 for DchpSeries Modules Port MirroringSimple Network-Management Protocol Snmp Redundant Switch ControllerRemote Monitoring Rmon Supervisor Module Downloading the Startup Configuration FileP580/P882 Chassis Slot Following error message in the CLI Switch PortsWeb AFT Issues Vlan IssuesFunctional Restrictions Auto-NegotiationCajunView Checksum Error MessageCPU Synchronization Legacy CLILink Status Distance Vector Multicast Routing Protocol DvmrpHunt Groups Oversized Packets Loopback TestsNetscape Software License Keying Redundant Controller SupportSpanning Tree Protocol STP 3Com TaggingTftp Download Status Delay Documentation Updates and CorrectionsCajun P550R/P880/P882 Switch User Guide Web AgentClick Interfaces Technical SupportCommand Setting the Priority of a PortExamples Setting a Port to Ignore Tag PriorityDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings