Avaya P880, P580, P550R manual Port Ranges for 80-Series Port Mirroring

Page 8

Table 2. Port Ranges for 80-Series Port Mirroring

Module

Port ranges that you can mirror

 

 

4-port gigabit modules

1–2

 

3–4

 

• Any single port

 

You can mirror any four single

 

ports simultaneously (one port per

 

channel). However you cannot

 

mirror a port range and a single

 

port within that range

 

simultaneously.

 

Example: You can mirror port 1

 

on channel 1, port 2 on channel 2,

 

and port 3 on channel 3

 

simultaneously. However, you

 

cannot mirror ports 1 through 2 on

 

channel 1 and port 2 on channel 2

 

simultaneously.

 

 

8-port gigabit modules

1–4

 

5–8

 

• Any single port

 

You can mirror any four single

 

ports simultaneously (one port per

 

channel). However you cannot

 

mirror a port range and a single

 

port within that range

 

simultaneously.

 

Example: You can mirror port 1

 

on channel 1, port 2 on channel 2,

 

and port 3 on channel 3

 

simultaneously. However, you

 

cannot mirror ports 1 through 4 on

 

channel 1 and port 2 on channel 2

 

simultaneously.

 

 

8

June 14, 2001

610-0184-095

Image 8
Contents Cajun P550R/P580/P880/P882 Switch Release Notes OverviewHardware New Hardware and Software FeaturesSoftware Features June 14 Supported Product Binaries and Boot Codes Queue Classification and Servicing FeaturesType of Switch Binary File Boot File OverviewClassification of Traffic Port Mirroring on 80-Series Modules WFQ Queue-Servicing AlgorithmConfiguring Port Mirroring By Using the CLI Setting Up Port MirroringPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel Configuring Port Mirroring By Using the Web Agent If you select ThenChanging the Status of Option 82 by Using the Web Agent Enabling Option 82 for DhcpChanging the Status of Option 82 by Using the CLI Changing the Status of Option 82 by Using SnmpMIB Item Cjnipv4serv.mibEnabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using the Web AgentEnabling MAC Address Lock and Traps by Using the CLI Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt, versionMIB, MIB Items, and OIDs for MAC Address Lock ProminetMib.txtEnhancements Changed CLI CommandsCorrected Problems Known Problems and Workarounds Command Line Interface CLIATM Uplink Modules Flood Rate LimitingFrames Transmitted with Cyclic Redundancy Check CRC Errors Desired Rate Web or CLI SettingIntelligent Multicasting Hot Swap ModulesIgmp Group Membership Table Example IPX L3 Forwarding CacheOption 82 for Dchp Point-to-Point Protocol PPP and TelnetPort Mirroring Series ModulesSimple Network-Management Protocol Snmp Redundant Switch ControllerRemote Monitoring Rmon Supervisor Module Downloading the Startup Configuration FileP580/P882 Chassis Slot Switch Ports Following error message in the CLIVlan Issues Web AFT IssuesFunctional Restrictions Auto-NegotiationChecksum Error Message CajunViewCPU Synchronization Legacy CLILink Status Distance Vector Multicast Routing Protocol DvmrpHunt Groups Oversized Packets Loopback TestsNetscape Redundant Controller Support Software License KeyingSpanning Tree Protocol STP 3Com TaggingDocumentation Updates and Corrections Tftp Download Status DelayCajun P550R/P880/P882 Switch User Guide Web AgentTechnical Support Click InterfacesSetting the Priority of a Port CommandSetting a Port to Ignore Tag Priority ExamplesDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings