Avaya P880, P580, P550R manual Setting a Rule in an Access Control List

Page 38

Examples

To display the settings of all of the ports on the module in slot 3, enter:

show port 3

To display the settings of ports 1 through 5 on the module in slot 3, enter:

show port 3/1-5

To display the settings of ports 1 through 5 on the module in slot 3 and of port 1 on the module in slot 6, enter:

show port 3/1-5,6/1

Setting a Rule in an Access Control List

Command

Use the access list command to set a rule on an access control list. The rule that you set will be applied on all of the ports on the switch. The command syntax is:

*Note: You must enable the access control list on which you want to set a rule. Only one access control list can be enabled at a time.

>configure)# access-list <access-list-name> <access-list-index> {permitdenyfwd1fwd2fwd3fwd4fwd5fwd6fwd7 fwd8} <protocol-id> {<source-ip-addr> <source- wildcard>anyhost <source-ip-addr>} [{lteqgtrange} <port> [<port>]] {<dest-ip-addr> <dest-wildcard>anyhost <dest-ip-addr>} [{lteqgtrange} <port> [<port>]] [established]

A-4

June 14, 2001

610-0184-095

Image 38
Contents Cajun P550R/P580/P880/P882 Switch Release Notes OverviewHardware New Hardware and Software FeaturesSoftware Features June 14 Type of Switch Binary File Boot File Supported Product Binaries and Boot CodesQueue Classification and Servicing Features OverviewClassification of Traffic Port Mirroring on 80-Series Modules WFQ Queue-Servicing AlgorithmConfiguring Port Mirroring By Using the CLI Setting Up Port MirroringPort Ranges for 80-Series Port Mirroring Port Ranges for 80-Series Port Mirroring Config# clear port mirror fabricmode2 channel channel Configuring Port Mirroring By Using the Web Agent If you select ThenChanging the Status of Option 82 by Using the Web Agent Enabling Option 82 for DhcpMIB Item Changing the Status of Option 82 by Using the CLIChanging the Status of Option 82 by Using Snmp Cjnipv4serv.mibEnabling Traps for Unknown Source Addresses Enabling MAC Address Lock and Traps by Using the Web AgentEnabling MAC Address Lock and Traps by Using the CLI Enabling MAC Address Lock and Traps by Using Snmp ProminetMib.txt, versionMIB, MIB Items, and OIDs for MAC Address Lock ProminetMib.txtEnhancements Changed CLI CommandsCorrected Problems ATM Uplink Modules Known Problems and WorkaroundsCommand Line Interface CLI Flood Rate LimitingFrames Transmitted with Cyclic Redundancy Check CRC Errors Desired Rate Web or CLI SettingIntelligent Multicasting Hot Swap ModulesIgmp Group Membership Table Example IPX L3 Forwarding CacheOption 82 for Dchp Point-to-Point Protocol PPP and TelnetPort Mirroring Series ModulesSimple Network-Management Protocol Snmp Redundant Switch ControllerRemote Monitoring Rmon Supervisor Module Downloading the Startup Configuration FileP580/P882 Chassis Slot Switch Ports Following error message in the CLIFunctional Restrictions Vlan IssuesWeb AFT Issues Auto-NegotiationCPU Synchronization Checksum Error MessageCajunView Legacy CLILink Status Distance Vector Multicast Routing Protocol DvmrpHunt Groups Oversized Packets Loopback TestsNetscape Spanning Tree Protocol STP Redundant Controller SupportSoftware License Keying 3Com TaggingCajun P550R/P880/P882 Switch User Guide Documentation Updates and CorrectionsTftp Download Status Delay Web AgentTechnical Support Click InterfacesSetting the Priority of a Port CommandSetting a Port to Ignore Tag Priority ExamplesDisplaying the Port Settings Setting a Rule in an Access Control List June 14 Displaying Access Control Lists Setting WFQ Correct syntax for Command 2 is Displaying the Queue Service Settings