Asante Technologies 35516 user manual User Access Verification Password

Page 15

Under the Settings tab, choose VT100 for Emulation mode

Select Terminal keys for Function, Arrow, and Ctrl keys. Be sure the setting is for Terminal keys, NOT Windows keys

Back under the Connect To tab, press the Configuration button

Set the data rate to 9600 Baud

Set data format to 8 data bits, 1 stop bit and no parity

Set flow control to NONE

Now that terminal is set up correctly, power on the switch (boot sequence will display in terminal.)

After connecting to the console, a prompt like the following will appear:

User Access Verification

Password:

By default, the initial password for access via console and telnet is Asante (case-sensitive). See the following section for setting new passwords on the terminal lines.

15

Image 15
Contents IntraCore 35516 Series Technical Support IntraCore 35516 SeriesTable of Contents Page Introduction FeaturesLEDs Package ContentsGbic Front and Back Panel DescriptionsConsole Interface Management and ConfigurationRecommended Installation Tools Hardware Installation and SetupInstallation Overview Safety OverviewCooling and Airflow Installation into an Equipment RackPower Requirements Environmental RequirementsGigabit Interface Converters Installing a GbicSystem Information System up since 103443 Fri Feb 07 Installing the Optional Emergency Power SupplyRemoving a Gbic Gbic Care and HandlingConnecting Power Connecting to the Network1 10/100/1000BaseT Ports Cabling Procedures Setup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console User Access Verification Password Specifies a Hidden line password will follow Setting PasswordsUnencrypted cleartext line password Specifies an Unencrypted line password will followConfiguring an IP Address Setting a Default IP Gateway AddressRouterconfig-if-veth1# Restoring Factory Defaults System Boot ParametersRouterconfig# boot system flash bank1bank2 Command Show ? Purpose Understanding the Command Line Interface CLIUser Top User Exec Mode Access Each Command ModePrivileged Top Privileged Exec Mode Router enable Password Router#Command Purpose Global Configuration Mode Command Purpose Router# configure terminalCommand Exit end Ctrl-Z Purpose Interface Configuration Mode Route-Map Configuration Mode Router Configuration ModeCommand Help Purpose Advanced Features Supported within the Command ModeRouterconfig# route Ambiguous command. Routerconfig# Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# routed rip Invalid input detected at markerRouterconfig# router Command incomplete. Routerconfig# Using CLI Command HistoryUsing the No and Default Forms of Commands Using Command-Line Editing Features and ShortcutsKeystrokes Purpose Moving Around on the Command LineCompleting a Partial Command Name Router# confTab Router# configureKeystrokes Purpose Press the Delete or Backspace Editing Command Lines that WrapRouter# co? configure copy Router# co Deleting EntriesControlling Capitalization Redisplaying the Current Command LineScrolling Down a Line or a Screen Transposing Mistyped CharactersRouterconfig-line# password Asante Passwords and Privileges CommandsEnable Password PasswordService Password-Encryption Managing the System Managing the System and Configuration FilesSetting the System Clock Changing the PasswordTest Connections with Ping Tests Enable the System LogDisplaying the Operating Configuration Trace Packet RoutesRouterconfig# hostname newname Newnameconfig# end Managing Configuration FilesConfiguring from the Terminal Configuration to NvramCopying Configuration Files to a Network Server Startup-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Running-configDisable the Snmp Protocol Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Routerconfig# duplicate-ip detectPriority Forward TimeHello Time Maximum AgePort Path Cost Routerconfig# mac-address-table aging-timeMAC Address Table Port PriorityClass Address or Range Status Configuring IPConfiguring IP Addressing Assign IP Addresses to Network InterfacesCommand Purpose Assign Multiple IP Addresses to Network InterfacesCidr Prefix Class C Equivalent Host Addresses Secondary Establish Address ResolutionConfiguring IP Routing Define a Static ARP CacheRoute Source Default Distance Configuring Static RoutesNeighbor ip-address Configuring RIPEnable RIP Allow Unicast Updates for RIPCommand Purpose Route-map map-tagdeny permit sequence Specify a RIP VersionRedistribute Routing Information Set Metrics for Redistributed Routes Set Administrative DistanceGenerate a Default Route Suppress Routing Updates through an InterfaceFiltering Routing Information Command Purpose Offset-list access-list-name in out Adjust TimersEnable or Disable Split-horizon Manage Authentication KeysMonitor and Maintain RIP Configuring IP Multicast RoutingConfiguring Igmp Modifying the Igmp Host-Query Message IntervalPurpose Ip igmp query-interval 1-65535 seconds Seconds CommandConfiguring the Router as a Statically Connected Member Changing the Igmp VersionNbr-timeout 35-8000 seconds Configuring DvmrpReport-interval Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Default value 200 secondsCreate a Standard Access List Using Access ListsDestination address to match. e.g Create an Expanded Access ListOperator greater then Creating an Access List with a NameApplying an Access List to an Interface Operator equal toCommand Purpose Router ospf Step Configuring OspfEnable Ospf Configure ABR TypeConfigure Compatibility Configure Ospf Interface ParametersConfigure Ospf Network Type Command Purpose Neighbor ip-address priority number Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Configure Ospf Not So Stubby Area NssaNot-advertised Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Create Virtual LinksRedistribute Routes into Ospf Control Default MetricsConfigure Route Calculation Timers Refresh Timer ConfigurationSuppress Routes on an Interface Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Command Purpose Distance ospf external distance1 inter-areaName Router ip-addressVirtual Router Redundancy Protocol Vrrp Vrrp ConfigurationChange Irdp Parameters Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Monitoring and Maintaining the NetworkShow ip irdp Command Purpose Show arp interfaceShow access-lists access-list Show ip prefix-list prefix-list-nameCreating or Modifying a Vlan Vlan ConfigurationRouterconfig# interface veth2 vlan Routerconfig-if-veth2# Routerconfig# no vlan Routerconfig# exit Router# show vlanDeleting a Vlan Static Access Vlan Port Membership ModesTrunk Ieee 802.1Q Command Purpose Routerconfig# vlan dot1q tag native 3 Dot1q TunnelTrunk allowed vlan add all except Mode dot1q-tunnel Problem Possible Solutions Appendix A. Basic TroubleshootingStandards Compliance Appendix B. SpecificationsPhysical Characteristics Technical Support and WarrantyAppendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration