Asante Technologies 35516 user manual Interface Configuration Mode

Page 22

Router# configure terminal

Router(config)# ?

access-list

Add an access list entry

arp

Set static arp entry

boot

Modify system boot parameters

duplicate-ip

Duplicate IP Address detection Global Commands

enable

Modify enable password parameters

end

End current mode and change to enable mode

exit

Exit current mode and down to previous mode

help

Description of the interactive help system

hostname

Set system's network name

interface

Select an interface to configure

ip

Global IP configuration subcommands

line

Configure a terminal line

logging

Message Logging global configuration commands

mac-address-table

MAC Address Table global configuration command

no

Negate a command or set its defaults

quit

Exit current mode and down to previous mode

route-map

Create route-map or enter route-map command mode

router

Enable a routing process

service

Set up miscellaneous service

snmp-server

Modify SNMP parameters

spanning-tree

Enable Spanning Tree Protocol

vlan

VLAN global configuration command

Router(config)#

 

From global configuration mode, you can access three additional configuration modes: The interface, router, and route-mapcommands are used to access their respective configuration modes.

3.3.1 Interface Configuration Mode

Many features are enabled on a per-interface basis. Interface configuration commands modify the operation of an interface such as an Ethernet or serial port. Interface configuration commands always follow an interface global configuration command, which defines the interface type (Ethernet or Virtual interfaces. The virtual interfaces are bound to VLANs and can be assigned IP addresses).

In the following example, Ethernet interface eth1 is about to be configured. The new prompt, Router(config-if-eth1)#, indicates the interface configuration mode. In this example, the user asks for help by requesting a list of commands.

Router(config)# interface eth1

Router(config-if-eth1)# ?

description

Interface specific description

end

End current mode and change to enable mode

exit

Exit current mode and down to previous mode

help

Description of the interactive help system

ip

Interface Internet Protocol config commands

mtu

Set the interface Maximum Transmission Unit (MTU)

no

Negate a command or set its defaults

quit

Exit current mode and down to previous mode

shutdown

Shutdown the selected interface

spanning-tree

Spanning Tree Protocol interface command

switchport

Port operating in L2 mode

Router(config-if-eth1)#

To exit interface configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to top mode, use the end command or press Ctrl-Z.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents IntraCore 35516 Series IntraCore 35516 Series Technical SupportTable of Contents Page Features IntroductionPackage Contents LEDsFront and Back Panel Descriptions GbicManagement and Configuration Console InterfaceSafety Overview Hardware Installation and SetupInstallation Overview Recommended Installation ToolsEnvironmental Requirements Installation into an Equipment RackPower Requirements Cooling and AirflowInstalling a Gbic Gigabit Interface ConvertersGbic Care and Handling Installing the Optional Emergency Power SupplyRemoving a Gbic System Information System up since 103443 Fri Feb 07Connecting to the Network Connecting Power1 10/100/1000BaseT Ports Cabling Procedures Gigabit Ethernet Ports Cabling Procedures SetupConnecting to a Console User Access Verification Password Specifies an Unencrypted line password will follow Setting PasswordsUnencrypted cleartext line password Specifies a Hidden line password will followSetting a Default IP Gateway Address Configuring an IP AddressRouterconfig-if-veth1# System Boot Parameters Restoring Factory DefaultsRouterconfig# boot system flash bank1bank2 Access Each Command Mode Understanding the Command Line Interface CLIUser Top User Exec Mode Command Show ? PurposeRouter enable Password Router# Privileged Top Privileged Exec ModeCommand Purpose Command Purpose Router# configure terminal Global Configuration ModeCommand Exit end Ctrl-Z Purpose Interface Configuration Mode Router Configuration Mode Route-Map Configuration ModeAdvanced Features Supported within the Command Mode Command Help PurposeRouterconfig# routed rip Invalid input detected at marker Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# route Ambiguous command. Routerconfig#Using Command-Line Editing Features and Shortcuts Using CLI Command HistoryUsing the No and Default Forms of Commands Routerconfig# router Command incomplete. Routerconfig#Router# confTab Router# configure Moving Around on the Command LineCompleting a Partial Command Name Keystrokes PurposeDeleting Entries Editing Command Lines that WrapRouter# co? configure copy Router# co Keystrokes Purpose Press the Delete or BackspaceTransposing Mistyped Characters Redisplaying the Current Command LineScrolling Down a Line or a Screen Controlling CapitalizationPassword Passwords and Privileges CommandsEnable Password Routerconfig-line# password AsanteService Password-Encryption Changing the Password Managing the System and Configuration FilesSetting the System Clock Managing the SystemTrace Packet Routes Enable the System LogDisplaying the Operating Configuration Test Connections with Ping TestsConfiguration to Nvram Managing Configuration FilesConfiguring from the Terminal Routerconfig# hostname newname Newnameconfig# endCopying Configuration Files to a Network Server Running-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Startup-configRouterconfig# duplicate-ip detect Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Disable the Snmp ProtocolMaximum Age Forward TimeHello Time PriorityPort Priority Routerconfig# mac-address-table aging-timeMAC Address Table Port Path CostAssign IP Addresses to Network Interfaces Configuring IPConfiguring IP Addressing Class Address or Range StatusAssign Multiple IP Addresses to Network Interfaces Command PurposeCidr Prefix Class C Equivalent Host Addresses Define a Static ARP Cache Establish Address ResolutionConfiguring IP Routing SecondaryConfiguring Static Routes Route Source Default DistanceAllow Unicast Updates for RIP Configuring RIPEnable RIP Neighbor ip-addressSpecify a RIP Version Command Purpose Route-map map-tagdeny permit sequenceRedistribute Routing Information Set Administrative Distance Set Metrics for Redistributed RoutesSuppress Routing Updates through an Interface Generate a Default RouteFiltering Routing Information Manage Authentication Keys Adjust TimersEnable or Disable Split-horizon Command Purpose Offset-list access-list-name in outConfiguring IP Multicast Routing Monitor and Maintain RIPModifying the Igmp Host-Query Message Interval Configuring IgmpPurpose Ip igmp query-interval 1-65535 seconds Changing the Igmp Version CommandConfiguring the Router as a Statically Connected Member SecondsConfiguring Dvmrp Nbr-timeout 35-8000 secondsDefault value 200 seconds Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Report-intervalUsing Access Lists Create a Standard Access ListCreate an Expanded Access List Destination address to match. e.gOperator equal to Creating an Access List with a NameApplying an Access List to an Interface Operator greater thenConfigure ABR Type Configuring OspfEnable Ospf Command Purpose Router ospf StepConfigure Ospf Interface Parameters Configure CompatibilityConfigure Ospf Network Type Configure Ospf Not So Stubby Area Nssa Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Command Purpose Neighbor ip-address priority numberCreate Virtual Links Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Not-advertisedRefresh Timer Configuration Control Default MetricsConfigure Route Calculation Timers Redistribute Routes into OspfCommand Purpose Distance ospf external distance1 inter-area Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Suppress Routes on an InterfaceRouter ip-address NameVrrp Configuration Virtual Router Redundancy Protocol VrrpMonitoring and Maintaining the Network Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Change Irdp ParametersShow ip prefix-list prefix-list-name Command Purpose Show arp interfaceShow access-lists access-list Show ip irdpVlan Configuration Creating or Modifying a VlanRouterconfig# no vlan Routerconfig# exit Router# show vlan Routerconfig# interface veth2 vlan Routerconfig-if-veth2#Deleting a Vlan Vlan Port Membership Modes Static AccessTrunk Ieee 802.1Q 3 Dot1q Tunnel Command Purpose Routerconfig# vlan dot1q tag nativeTrunk allowed vlan add all except Mode dot1q-tunnel Appendix A. Basic Troubleshooting Problem Possible SolutionsTechnical Support and Warranty Appendix B. SpecificationsPhysical Characteristics Standards ComplianceFCC Compliance Statement Important Safety Instructions Appendix C. FCC Compliance and Warranty StatementsIntraCare Warranty Statement Page Pin Number Signal Name Appendix D. Console Port Pin OutsAppendix E. Online Warranty Registration
Top Page Image Contents