Asante Technologies 35516 user manual 3 Dot1q Tunnel, Trunk allowed vlan add all except

Page 70

Use the following commands to configure the VLAN Allowed List for the trunk port:

Command

Purpose

Router(config)# interface IFNAME

Enter the interface name to access the interface

 

configuration node.

 

 

Router(config-if-IFNAME)# switchport

This command designates the interface as IEEE

mode trunk

802.1q trunk-access mode.

 

Use the no form of this command to reset to the

 

default of static-access mode.

 

 

Router(config-if-IFNAME)# switchport

This command will configure the VLAN Allowed

trunk allowed vlan {add all except

List for the trunk port.

remove} vlan-list

add - Add VLANs to the current VLAN list

 

 

all – Add all VLANs to the allowed-VLAN list

 

except – Add all VLANs except those specified

 

in the VLAN list

 

remove – Remove the VLANs specified in the

 

VLAN list.

 

vlan-list– The VLAN list can be a single VLAN

 

or a range of VLANs (from 1-4094). Separate the

 

VID number by a comma, or by a hyphen when

 

listing a range (i.e. 120, 158, 4090-4094)

 

Use the no form of this command to reset to

 

default setting of all VLANs in the VLAN Allowed

 

List.

 

 

Router(config-if-IFNAME)# end

Return to Enable node.

 

 

The trunk port accepts tagged and untagged frames. All the untagged frames are classified to the trunk port’s native VLAN (the VLAN whose VID matches the port’s VLAN ID). The trunk port also sends out the frames as untagged for the native VLAN. Using the following global configuration command can change this behavior:

Command

Purpose

Router(config)# vlan dot1q tag native

This global command enables tagging of native

 

VLAN frames on all 802.1Q trunk ports.

 

Use the no form of this command to disable

 

tagging of native VLAN frames.

Router(config)# end

Return to Enable node.

6.2.3 Dot1q Tunnel

802.1Q tunnel ports are used to maintain customer VLAN integrity across a service provider network. You can configure a tunnel port on an edge switch in the service provider network and connect it to an 802.1Q trunk port on a customer interface, creating an asymmetric link. A tunnel port belongs to a single VLAN that is dedicated to tunneling.

70

Image 70
Contents IntraCore 35516 Series IntraCore 35516 Series Technical SupportTable of Contents Page Features IntroductionPackage Contents LEDsFront and Back Panel Descriptions GbicManagement and Configuration Console InterfaceSafety Overview Hardware Installation and SetupInstallation Overview Recommended Installation ToolsEnvironmental Requirements Installation into an Equipment RackPower Requirements Cooling and AirflowInstalling a Gbic Gigabit Interface ConvertersGbic Care and Handling Installing the Optional Emergency Power SupplyRemoving a Gbic System Information System up since 103443 Fri Feb 07Connecting to the Network Connecting Power1 10/100/1000BaseT Ports Cabling Procedures Gigabit Ethernet Ports Cabling Procedures SetupConnecting to a Console User Access Verification Password Specifies an Unencrypted line password will follow Setting PasswordsUnencrypted cleartext line password Specifies a Hidden line password will followSetting a Default IP Gateway Address Configuring an IP AddressRouterconfig-if-veth1# System Boot Parameters Restoring Factory DefaultsRouterconfig# boot system flash bank1bank2 Access Each Command Mode Understanding the Command Line Interface CLIUser Top User Exec Mode Command Show ? PurposeRouter enable Password Router# Privileged Top Privileged Exec ModeCommand Purpose Command Purpose Router# configure terminal Global Configuration ModeCommand Exit end Ctrl-Z Purpose Interface Configuration Mode Router Configuration Mode Route-Map Configuration ModeAdvanced Features Supported within the Command Mode Command Help PurposeRouterconfig# routed rip Invalid input detected at marker Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# route Ambiguous command. Routerconfig#Using Command-Line Editing Features and Shortcuts Using CLI Command HistoryUsing the No and Default Forms of Commands Routerconfig# router Command incomplete. Routerconfig#Router# confTab Router# configure Moving Around on the Command LineCompleting a Partial Command Name Keystrokes PurposeDeleting Entries Editing Command Lines that WrapRouter# co? configure copy Router# co Keystrokes Purpose Press the Delete or BackspaceTransposing Mistyped Characters Redisplaying the Current Command LineScrolling Down a Line or a Screen Controlling CapitalizationPassword Passwords and Privileges CommandsEnable Password Routerconfig-line# password AsanteService Password-Encryption Changing the Password Managing the System and Configuration FilesSetting the System Clock Managing the SystemTrace Packet Routes Enable the System LogDisplaying the Operating Configuration Test Connections with Ping TestsConfiguration to Nvram Managing Configuration FilesConfiguring from the Terminal Routerconfig# hostname newname Newnameconfig# endCopying Configuration Files to a Network Server Running-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Startup-configRouterconfig# duplicate-ip detect Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Disable the Snmp ProtocolMaximum Age Forward TimeHello Time PriorityPort Priority Routerconfig# mac-address-table aging-timeMAC Address Table Port Path CostAssign IP Addresses to Network Interfaces Configuring IPConfiguring IP Addressing Class Address or Range StatusAssign Multiple IP Addresses to Network Interfaces Command PurposeCidr Prefix Class C Equivalent Host Addresses Define a Static ARP Cache Establish Address ResolutionConfiguring IP Routing SecondaryConfiguring Static Routes Route Source Default DistanceAllow Unicast Updates for RIP Configuring RIPEnable RIP Neighbor ip-addressSpecify a RIP Version Command Purpose Route-map map-tagdeny permit sequenceRedistribute Routing Information Set Administrative Distance Set Metrics for Redistributed RoutesSuppress Routing Updates through an Interface Generate a Default RouteFiltering Routing Information Manage Authentication Keys Adjust TimersEnable or Disable Split-horizon Command Purpose Offset-list access-list-name in outConfiguring IP Multicast Routing Monitor and Maintain RIPModifying the Igmp Host-Query Message Interval Configuring IgmpPurpose Ip igmp query-interval 1-65535 seconds Changing the Igmp Version CommandConfiguring the Router as a Statically Connected Member SecondsConfiguring Dvmrp Nbr-timeout 35-8000 secondsDefault value 200 seconds Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Report-intervalUsing Access Lists Create a Standard Access ListCreate an Expanded Access List Destination address to match. e.gOperator equal to Creating an Access List with a NameApplying an Access List to an Interface Operator greater thenConfigure ABR Type Configuring OspfEnable Ospf Command Purpose Router ospf StepConfigure Ospf Interface Parameters Configure CompatibilityConfigure Ospf Network Type Configure Ospf Not So Stubby Area Nssa Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Command Purpose Neighbor ip-address priority numberCreate Virtual Links Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Not-advertisedRefresh Timer Configuration Control Default MetricsConfigure Route Calculation Timers Redistribute Routes into OspfCommand Purpose Distance ospf external distance1 inter-area Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Suppress Routes on an InterfaceRouter ip-address NameVrrp Configuration Virtual Router Redundancy Protocol VrrpMonitoring and Maintaining the Network Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Change Irdp ParametersShow ip prefix-list prefix-list-name Command Purpose Show arp interfaceShow access-lists access-list Show ip irdpVlan Configuration Creating or Modifying a VlanRouterconfig# no vlan Routerconfig# exit Router# show vlan Routerconfig# interface veth2 vlan Routerconfig-if-veth2#Deleting a Vlan Vlan Port Membership Modes Static AccessTrunk Ieee 802.1Q 3 Dot1q Tunnel Command Purpose Routerconfig# vlan dot1q tag nativeTrunk allowed vlan add all except Mode dot1q-tunnel Appendix A. Basic Troubleshooting Problem Possible SolutionsTechnical Support and Warranty Appendix B. SpecificationsPhysical Characteristics Standards ComplianceFCC Compliance Statement Important Safety Instructions Appendix C. FCC Compliance and Warranty StatementsIntraCare Warranty Statement Page Pin Number Signal Name Appendix D. Console Port Pin OutsAppendix E. Online Warranty Registration