Asante Technologies 35516 user manual Router Configuration Mode, Route-Map Configuration Mode

Page 23

3.3.2 Router Configuration Mode

Router configuration commands are used to configure an IP routing protocol and always follow a router command. To list the available router configuration keywords, enter the router command followed by a space and a question mark (?) at the global configuration prompt.

Router(config)# router ?

ospf

Open Shortest Path First

rip

Routing Information Protocol (RIP)

Router(config)# router

In the following example, the router is configured to support the Routing Information Protocol (RIP). The new prompt is Router(config-rip-router)#.

Router(config)# router rip

Router(config-rip-router)# ?

default-information

Control distribution of default route

default-metric

Set a metric of redistribute routes

distance

Administrative distance

distribute-list

Filter networks in routing updates

end

End current mode and change to enable mode

exit

Exit current mode and down to previous mode

help

Description of the interactive help system

neighbor

Specify a neighbor router

network

Enable routing on an IP network

no

Negate a command or set its defaults

offset-list

Modify RIP metric

passive-interface

Suppress routing updates on an interface

quit

Exit current mode and down to previous mode

redistribute

Redistribute information from another routing protocol

timers

Adjust routing timers

version

Set routing protocol version

Router(config-rip-router)#

To exit router configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to privileged EXEC mode, use the end command or press Ctrl-Z.

3.3.3 Route-Map Configuration Mode

Use the route-map configuration mode to configure the routing table and the source and destination information. To access and list the route-map configuration commands, enter route-mapcommand at the global configuration mode.

In the following example, a route map named mymap is configured. The new prompt is Router(config-route- map)#. Enter a question mark (?) to list route-mapconfiguration commands.

Router(config)# route-map

mymap permit 30

Router(config-route-map)#

?

end

End current mode and change to enable mode

exit

Exit current mode and down to previous mode

help

Description of the interactive help system

match

Match values from routing table

no

Negate a command or set its defaults

on-match

Exit policy on matches

quit

Exit current mode and down to previous mode

route-map

Create route-map or enter route-map command mode

set

Set values in destination routing protocol

Router(config-route-map)#

To exit route-map configuration mode and return to global configuration mode, enter the exit command. To exit configuration mode and return to privileged EXEC mode, use the end command or press Ctrl-Z.

23

Image 23
Contents IntraCore 35516 Series Technical Support IntraCore 35516 SeriesTable of Contents Page Introduction FeaturesLEDs Package ContentsGbic Front and Back Panel DescriptionsConsole Interface Management and ConfigurationRecommended Installation Tools Hardware Installation and SetupInstallation Overview Safety OverviewCooling and Airflow Installation into an Equipment RackPower Requirements Environmental RequirementsGigabit Interface Converters Installing a GbicSystem Information System up since 103443 Fri Feb 07 Installing the Optional Emergency Power SupplyRemoving a Gbic Gbic Care and Handling1 10/100/1000BaseT Ports Cabling Procedures Connecting PowerConnecting to the Network Connecting to a Console SetupGigabit Ethernet Ports Cabling Procedures User Access Verification Password Specifies a Hidden line password will follow Setting PasswordsUnencrypted cleartext line password Specifies an Unencrypted line password will followRouterconfig-if-veth1# Configuring an IP AddressSetting a Default IP Gateway Address Routerconfig# boot system flash bank1bank2 Restoring Factory DefaultsSystem Boot Parameters Command Show ? Purpose Understanding the Command Line Interface CLIUser Top User Exec Mode Access Each Command ModeCommand Purpose Privileged Top Privileged Exec ModeRouter enable Password Router# Command Exit end Ctrl-Z Purpose Global Configuration ModeCommand Purpose Router# configure terminal Interface Configuration Mode Route-Map Configuration Mode Router Configuration ModeCommand Help Purpose Advanced Features Supported within the Command ModeRouterconfig# route Ambiguous command. Routerconfig# Checking Command SyntaxRouterconfig# hostname ? Word This systems network name Routerconfig# routed rip Invalid input detected at markerRouterconfig# router Command incomplete. Routerconfig# Using CLI Command HistoryUsing the No and Default Forms of Commands Using Command-Line Editing Features and ShortcutsKeystrokes Purpose Moving Around on the Command LineCompleting a Partial Command Name Router# confTab Router# configureKeystrokes Purpose Press the Delete or Backspace Editing Command Lines that WrapRouter# co? configure copy Router# co Deleting EntriesControlling Capitalization Redisplaying the Current Command LineScrolling Down a Line or a Screen Transposing Mistyped CharactersRouterconfig-line# password Asante Passwords and Privileges CommandsEnable Password PasswordService Password-Encryption Managing the System Managing the System and Configuration FilesSetting the System Clock Changing the PasswordTest Connections with Ping Tests Enable the System LogDisplaying the Operating Configuration Trace Packet RoutesRouterconfig# hostname newname Newnameconfig# end Managing Configuration FilesConfiguring from the Terminal Configuration to NvramCopying Configuration Files to a Network Server Startup-config Configuring Snmp and Spanning TreeConfiguring Snmp Support Running-configDisable the Snmp Protocol Configuring Spanning Tree Protocol STPCreate or Modify Access Control for Snmp Community Routerconfig# duplicate-ip detectPriority Forward TimeHello Time Maximum AgePort Path Cost Routerconfig# mac-address-table aging-timeMAC Address Table Port PriorityClass Address or Range Status Configuring IPConfiguring IP Addressing Assign IP Addresses to Network InterfacesCidr Prefix Class C Equivalent Host Addresses Command PurposeAssign Multiple IP Addresses to Network Interfaces Secondary Establish Address ResolutionConfiguring IP Routing Define a Static ARP CacheRoute Source Default Distance Configuring Static RoutesNeighbor ip-address Configuring RIPEnable RIP Allow Unicast Updates for RIPRedistribute Routing Information Command Purpose Route-map map-tagdeny permit sequenceSpecify a RIP Version Set Metrics for Redistributed Routes Set Administrative DistanceFiltering Routing Information Generate a Default RouteSuppress Routing Updates through an Interface Command Purpose Offset-list access-list-name in out Adjust TimersEnable or Disable Split-horizon Manage Authentication KeysMonitor and Maintain RIP Configuring IP Multicast RoutingPurpose Ip igmp query-interval 1-65535 seconds Configuring IgmpModifying the Igmp Host-Query Message Interval Seconds CommandConfiguring the Router as a Statically Connected Member Changing the Igmp VersionNbr-timeout 35-8000 seconds Configuring DvmrpReport-interval Default value 180 secondsCommand Purpose Route-expire-time 20-4000 seconds Default value 200 secondsCreate a Standard Access List Using Access ListsDestination address to match. e.g Create an Expanded Access ListOperator greater then Creating an Access List with a NameApplying an Access List to an Interface Operator equal toCommand Purpose Router ospf Step Configuring OspfEnable Ospf Configure ABR TypeConfigure Ospf Network Type Configure CompatibilityConfigure Ospf Interface Parameters Command Purpose Neighbor ip-address priority number Configure Ospf for Non-broadcast NetworksConfigure Area Parameters Configure Ospf Not So Stubby Area NssaNot-advertised Configure Route Summarization between Ospf AreasCommand Purpose Area area-idvirtual-link router-idhello Create Virtual LinksRedistribute Routes into Ospf Control Default MetricsConfigure Route Calculation Timers Refresh Timer ConfigurationSuppress Routes on an Interface Change the Ospf Administrative DistancesPrevent Routes from being Advertised in Routing Updates Command Purpose Distance ospf external distance1 inter-areaName Router ip-addressVirtual Router Redundancy Protocol Vrrp Vrrp ConfigurationChange Irdp Parameters Configuring Icmp Router Discovery Protocol IrdpEnable Irdp Processing Monitoring and Maintaining the NetworkShow ip irdp Command Purpose Show arp interfaceShow access-lists access-list Show ip prefix-list prefix-list-nameCreating or Modifying a Vlan Vlan ConfigurationDeleting a Vlan Routerconfig# interface veth2 vlan Routerconfig-if-veth2#Routerconfig# no vlan Routerconfig# exit Router# show vlan Trunk Ieee 802.1Q Static AccessVlan Port Membership Modes Trunk allowed vlan add all except Command Purpose Routerconfig# vlan dot1q tag native3 Dot1q Tunnel Mode dot1q-tunnel Problem Possible Solutions Appendix A. Basic TroubleshootingStandards Compliance Appendix B. SpecificationsPhysical Characteristics Technical Support and WarrantyIntraCare Warranty Statement Appendix C. FCC Compliance and Warranty StatementsFCC Compliance Statement Important Safety Instructions Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration