Asante Technologies 35516 Configuring Spanning Tree Protocol STP, Disable the Snmp Protocol

Page 37

Create or Modify Access Control for SNMP Community

You can configure a community string, which acts like a password, to permit access to the agent on the router.

Read Only (ro): The string that defines access rights for reading SNMP data objects. The default is public.

Read-Write (rw): The string that defines access rights for writing SNMP data objects. The default is private.

Important! Be sure to change the SNMP default community strings in order to prevent unauthorized access to management information.

To set up the community access string to permit access to the SNMP, use the following command from the global command mode.

Command

Purpose

snmp-server community string

Define the community access string.

{ro rw}

 

Establish the Contact, and Location of the SNMP Agent

Set the system contact and the location of the SNMP agent so that these descriptions can be accessed through the configuration file.

To set the system contact (sysContact) string, use the following command in global configuration command.

Command

Purpose

snmp-server contact text

Set the system contact string.

snmp-server location text

Set the system location string.

Define SNMP Trap Operations

 

A trap is an unsolicited message sent by an SNMP agent to an SNMP manager indicating that some event has occurred. The SNMP trap operations allow the user to configure the router to send information to a network management application when a particular event occurs.

To define traps for the agent to send to the manager, use the following commands in global configuration mode.

Command

Purpose

snmp-server host address

Specify the recipient of the trap message.

The 35516 can send an SNMP trap to its configured trap receivers if it detects a duplicate IP address. To turn on duplicate IP detection, use the following command in global configuration mode:

Router(config)# duplicate-ip detect

Disable the SNMP Protocol

To disable SNMP, use the following command in global configuration mode:

Command

Purpose

no snmp-server

Disable SNMP operation.

4.3.2 Configuring Spanning Tree Protocol (STP)

The Spanning Tree Protocol (STP) is part of the IEEE 802.1D standard. It provides for a redundant network without the redundant traffic through closed paths. For example, in a network without spanning tree protocol, the same message will be broadcast through multiple paths, which may start an unending packet-passing cycle. This in turn causes a great amount of extra network traffic, leading to network downtime. The STP reduces a network like this, with multiple, redundant connections, to one in which all points are connected,

37

Image 37
Contents IntraCore 35516 Series Technical Support IntraCore 35516 SeriesTable of Contents Page Introduction FeaturesLEDs Package ContentsGbic Front and Back Panel DescriptionsConsole Interface Management and ConfigurationInstallation Overview Hardware Installation and SetupSafety Overview Recommended Installation ToolsPower Requirements Installation into an Equipment RackEnvironmental Requirements Cooling and AirflowGigabit Interface Converters Installing a GbicRemoving a Gbic Installing the Optional Emergency Power SupplyGbic Care and Handling System Information System up since 103443 Fri Feb 07Connecting to the Network Connecting Power1 10/100/1000BaseT Ports Cabling Procedures Gigabit Ethernet Ports Cabling Procedures SetupConnecting to a Console User Access Verification Password Unencrypted cleartext line password Setting PasswordsSpecifies an Unencrypted line password will follow Specifies a Hidden line password will followSetting a Default IP Gateway Address Configuring an IP AddressRouterconfig-if-veth1# System Boot Parameters Restoring Factory DefaultsRouterconfig# boot system flash bank1bank2 User Top User Exec Mode Understanding the Command Line Interface CLIAccess Each Command Mode Command Show ? PurposeRouter enable Password Router# Privileged Top Privileged Exec ModeCommand Purpose Command Purpose Router# configure terminal Global Configuration ModeCommand Exit end Ctrl-Z Purpose Interface Configuration Mode Route-Map Configuration Mode Router Configuration ModeCommand Help Purpose Advanced Features Supported within the Command ModeRouterconfig# hostname ? Word This systems network name Checking Command SyntaxRouterconfig# routed rip Invalid input detected at marker Routerconfig# route Ambiguous command. Routerconfig#Using the No and Default Forms of Commands Using CLI Command HistoryUsing Command-Line Editing Features and Shortcuts Routerconfig# router Command incomplete. Routerconfig#Completing a Partial Command Name Moving Around on the Command LineRouter# confTab Router# configure Keystrokes PurposeRouter# co? configure copy Router# co Editing Command Lines that WrapDeleting Entries Keystrokes Purpose Press the Delete or BackspaceScrolling Down a Line or a Screen Redisplaying the Current Command LineTransposing Mistyped Characters Controlling CapitalizationEnable Password Passwords and Privileges CommandsPassword Routerconfig-line# password AsanteService Password-Encryption Setting the System Clock Managing the System and Configuration FilesChanging the Password Managing the SystemDisplaying the Operating Configuration Enable the System LogTrace Packet Routes Test Connections with Ping TestsConfiguring from the Terminal Managing Configuration FilesConfiguration to Nvram Routerconfig# hostname newname Newnameconfig# endCopying Configuration Files to a Network Server Configuring Snmp Support Configuring Snmp and Spanning TreeRunning-config Startup-configCreate or Modify Access Control for Snmp Community Configuring Spanning Tree Protocol STPRouterconfig# duplicate-ip detect Disable the Snmp ProtocolHello Time Forward TimeMaximum Age PriorityMAC Address Table Routerconfig# mac-address-table aging-timePort Priority Port Path CostConfiguring IP Addressing Configuring IPAssign IP Addresses to Network Interfaces Class Address or Range StatusAssign Multiple IP Addresses to Network Interfaces Command PurposeCidr Prefix Class C Equivalent Host Addresses Configuring IP Routing Establish Address ResolutionDefine a Static ARP Cache SecondaryRoute Source Default Distance Configuring Static RoutesEnable RIP Configuring RIPAllow Unicast Updates for RIP Neighbor ip-addressSpecify a RIP Version Command Purpose Route-map map-tagdeny permit sequenceRedistribute Routing Information Set Metrics for Redistributed Routes Set Administrative DistanceSuppress Routing Updates through an Interface Generate a Default RouteFiltering Routing Information Enable or Disable Split-horizon Adjust TimersManage Authentication Keys Command Purpose Offset-list access-list-name in outMonitor and Maintain RIP Configuring IP Multicast RoutingModifying the Igmp Host-Query Message Interval Configuring IgmpPurpose Ip igmp query-interval 1-65535 seconds Configuring the Router as a Statically Connected Member CommandChanging the Igmp Version SecondsNbr-timeout 35-8000 seconds Configuring DvmrpCommand Purpose Route-expire-time 20-4000 seconds Default value 180 secondsDefault value 200 seconds Report-intervalCreate a Standard Access List Using Access ListsDestination address to match. e.g Create an Expanded Access ListApplying an Access List to an Interface Creating an Access List with a NameOperator equal to Operator greater thenEnable Ospf Configuring OspfConfigure ABR Type Command Purpose Router ospf StepConfigure Ospf Interface Parameters Configure CompatibilityConfigure Ospf Network Type Configure Area Parameters Configure Ospf for Non-broadcast NetworksConfigure Ospf Not So Stubby Area Nssa Command Purpose Neighbor ip-address priority numberCommand Purpose Area area-idvirtual-link router-idhello Configure Route Summarization between Ospf AreasCreate Virtual Links Not-advertisedConfigure Route Calculation Timers Control Default MetricsRefresh Timer Configuration Redistribute Routes into OspfPrevent Routes from being Advertised in Routing Updates Change the Ospf Administrative DistancesCommand Purpose Distance ospf external distance1 inter-area Suppress Routes on an InterfaceName Router ip-addressVirtual Router Redundancy Protocol Vrrp Vrrp ConfigurationEnable Irdp Processing Configuring Icmp Router Discovery Protocol IrdpMonitoring and Maintaining the Network Change Irdp ParametersShow access-lists access-list Command Purpose Show arp interfaceShow ip prefix-list prefix-list-name Show ip irdpCreating or Modifying a Vlan Vlan ConfigurationRouterconfig# no vlan Routerconfig# exit Router# show vlan Routerconfig# interface veth2 vlan Routerconfig-if-veth2#Deleting a Vlan Vlan Port Membership Modes Static AccessTrunk Ieee 802.1Q 3 Dot1q Tunnel Command Purpose Routerconfig# vlan dot1q tag nativeTrunk allowed vlan add all except Mode dot1q-tunnel Problem Possible Solutions Appendix A. Basic TroubleshootingPhysical Characteristics Appendix B. SpecificationsTechnical Support and Warranty Standards ComplianceFCC Compliance Statement Important Safety Instructions Appendix C. FCC Compliance and Warranty StatementsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration