Motorola MVME3100 manual Flammability

Page 4

Flammability

All Motorola PWBs (printed wiring boards) are manufactured with a flammability rating of 94V-0 by UL-recognized manufacturers.

!

Caution

EMI Caution

This equipment generates, uses and can radiate electromagnetic energy. It may cause or be susceptible to electromagnetic interference (EMI) if not installed and used with adequate EMI protection.

Lithium Battery Caution

This product contains a lithium battery to power the clock and calendar circuitry.

Danger of explosion if battery is replaced incorrectly. Replace battery only

!with the same or equivalent type recommended by the equipment

Caution

manufacturer. Dispose of used batteries according to the manufacturer’s

instructions.

 

Il y a danger d’explosion s’il y a remplacement incorrect de la batterie.

!Remplacer uniquement avec une batterie du même type ou d’un type

Attention

équivalent recommandé par le constructeur. Mettre au rebut les batteries

usagées conformément aux instructions du fabricant.

 

Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur

!durch denselben oder einen vom Hersteller empfohlenen Typ. Entsorgung

Vorsicht

gebrauchter Batterien nach Angaben des Herstellers.

 

Image 4
Contents Installation and Use Page Safety Summary Flammability CE Notice European Community Limited and Restricted Rights Legend Contents Functional Description Specifications List of Figures 13. MVME721 Host I/O Connector J10 Pin Assignments List of TablesOverview of Contents About This ManualComments and Suggestions Conventions Used in This ManualHardware Preparation and Installation IntroductionDescription Getting StartedUnpacking Guidelines Overview of Startup ProceduresStartup Overview Hardware Configuration MVME3100 LayoutMVME3100 Board Layout Configuration Switch S4 Settings Configuration Switch S4Setting Switch Pos OFF Factory Default Geographical Address Switch Assignments Geographical Address Switch S3Slot Geographical Address Settings PMC I/O Voltage Configuration RTM Seeprom Address Switch S1RTM Eeprom Address Switch Assignments Function Not UsedHardware Installation Installing the MVME3100 into a ChassisEeprom Address Settings Device Address A20MVME3100 Connectors MVME721 Rear Transition Module ConnectorsConnector Function Connection to PeripheralsCompleting the Installation Applying Power Switches and IndicatorsFront-Panel LED Status Indicators Startup and OperationMVME721 LED Status Indicators Additional Onboard Status IndicatorsGenet DS3 MOTLoad Commands MOTLoad FirmwareOverview MOTLoad Implementation and Memory RequirementsMOTLoad Utility Applications MOTLoad TestsUsing MOTLoad Command Line InterfaceCommand Line Help Command Line RulesMOTLoad Command List MOTLoad CommandsCommand Description DownLoad ErrorDisplayNetBoot EchoCommand Description NetStats ResetNoCm PciDataRdMOTLoad Commands Default VME Settings MVME3100 vmeCfg -s -mMVME3100 vmeCfg -s -o1 CR/CSR Settings Firmware SettingsDisplaying VME Settings Editing VME Settings Restoring Default VME Settings Deleting VME SettingsRemote Start Slot Position CS/CSR Starting Address Alternate Boot Images and Safe Start Firmware Startup Sequence Following ResetFirmware Scan for Boot Image Address UsageChecksum Algorithm Valid Boot ImagesName Type Size MOTLoad Image Flags User ImagesMOTLoad Image Flags Name Value InterpretationAlternate Boot Data Structure MOTLoad Firmware Features MVME3100 Features SummaryFeature Description Functional DescriptionFunctional Description MVME721 RTM Features Summary Block Diagrams MVME3100 Block DiagramSystem Memory ProcessorLocal Bus Interface I2C Serial Interface and Devices Control and Timers LogicFlash Memory Ethernet Interfaces Asynchronous Serial PortsPCI/PCI-X Interfaces and Devices MPC8540 PCI-X InterfaceTSi148 VME Controller Serial ATA Host ControllerPCI-X-to-PCI-X Bridges PCI Mezzanine Card SlotsReal-time Clock Battery General-Purpose TimersPMC Expansion Reset Control Logic Debug SupportPin Assignments Connectors PMC Expansion Connector J4PMC Expansion Connector J4 Pin Assignments Pin SignalPAR Ethernet Connectors Pin Assignment Ethernet Connectors GENET1/J41B, GENET2/J2B, ENET1/J2APin # Signal 1000 Mb/s 10/100 Mb/s PCI Mezzanine Card PMC Connectors J11 J14, J21 J23 PMC Slot 1 Connector J11 Pin AssignmentsPMC Slot 1 Connector J12 Pin Assignments PMC Slot 1 Connector J13 Pin Assignments PMC Slot 1 Connector J14 Pin Assignments PMC Slot 2 Connector J21 Pin Assignments PMC Slot 2 Connector J22 Pin Assignments PMC Slot 2 Connector J23 Pin Assignments Serial Port Connectors COM1/J41A, COM2-COM5/J2A-D 10. COM Port Connector Pin AssignmentsVMEbus P1 Connector 11. VMEbus P1 Connector Pin Assignments12. VME P2 Connector Pinouts VMEbus P2 ConnectorPin P2-Z P2-A P2-B P2-C P2-D MVME721 PMC I/O Module PIM Connectors J10, J14 13. MVME721 Host I/O Connector J10 Pin AssignmentsPlanar sATA Power Connector J30 USB Connector J2714. Planar sATA Power Connector J30 Pin Assignments 15. USB Connector J27 Pin AssignmentsSATA Connectors J28 and J29 16. sATA Connectors J28 and J29 Pin AssignmentsHeaders Boundary Scan Header J24Processor COP Header J25 18. Processor COP Header J25 Pin AssignmentsPower Requirements Environmental SpecificationsModel Power Characteristics SpecificationsAppendix a Specifications Motorola Computer Group Documents Related DocumentationTable B-1. Motorola Computer Group Documents Table B-2. Manufacturers’ Documents Manufacturers’ DocumentsDocument Title and Source Publication Number Table B-2. Manufacturers’ Documents Table B-3. Related Specifications Related SpecificationsIeee http//standards.ieee.org/catalog