Motorola MVME3100 manual MVME721 PMC I/O Module PIM Connectors J10, J14

Page 72

Chapter 5 Pin Assignments

Table 5-12. VME P2 Connector Pinouts (continued)

Pin	P2-Z	P2-A	P2-B	P2-C	P2-D
29	SP4CTS	PMC1_IO58	VD30	PMC1_IO57	E2-1-

30	GND	PMC1_IO60	VD31	PMC1_IO59	E2-1+

31	SP4RTS	PMC1_IO62	GND	PMC1_IO61	GND

32	GND	PMC1_IO64	+5V	PMC1_IO63	+5V

MVME721 PMC I/O Module (PIM) Connectors (J10, J14)

PMC Host I/O connector J10 routes only power and ground from VME P2. There are no Host I/O signals on this connector. The MVME3100 routes PMC I/O from J14 of PMC Slot 1 to VME P2 rows A and C. The MVME721 routes these signals (pin-for-pin) from VME P2 to PMC I/O Module connector J14. See Table 5-13and Table 5-6for the pin assignments.

Table 5-13. MVME721 Host I/O Connector (J10) Pin Assignments

1	No Connect	No Connect	2

3	No Connect	No Connect	4

5	+5V	No Connect	6

7	No Connect	No Connect	8

9	No Connect	+3.3V	10

11	No Connect	No Connect	12

13	GND	No Connect	14

15	No Connect	No Connect	16

17	No Connect	GND	18

19	No Connect	No Connect	20

21	+5V	No Connect	22

23	No Connect	No Connect	24

25	No Connect	+3.3V	26

27	No Connect	No Connect	28

29	GND	No Connect	30

31	No Connect	No Connect	32

33	No Connect	GND	34

35	No Connect	No Connect	36

37	+5V	No Connect	38

39	No Connect	No Connect	40

41	No Connect	+3.3V	42

43	No Connect	No Connect	44

45	GND	No Connect	46

47	No Connect	No Connect	48

MVME3100 Installation and Use (V3100A/IH1)

61

Image 72

Contents Installation and Use Page Safety Summary Flammability CE Notice European Community Limited and Restricted Rights Legend Contents Functional Description Specifications List of Figures 13. MVME721 Host I/O Connector J10 Pin Assignments List of TablesOverview of Contents About This ManualComments and Suggestions Conventions Used in This ManualHardware Preparation and Installation IntroductionDescription Getting StartedOverview of Startup Procedures Unpacking GuidelinesStartup Overview Hardware Configuration MVME3100 LayoutMVME3100 Board Layout Configuration Switch S4 Configuration Switch S4 SettingsSetting Switch Pos OFF Factory Default Geographical Address Switch S3 Geographical Address Switch AssignmentsSlot Geographical Address Settings PMC I/O Voltage Configuration RTM Seeprom Address Switch S1RTM Eeprom Address Switch Assignments Function Not UsedHardware Installation Installing the MVME3100 into a ChassisEeprom Address Settings Device Address A20MVME3100 Connectors MVME721 Rear Transition Module ConnectorsConnector Function Connection to PeripheralsCompleting the Installation Applying Power Switches and IndicatorsFront-Panel LED Status Indicators Startup and OperationMVME721 LED Status Indicators Additional Onboard Status IndicatorsGenet DS3 MOTLoad Commands MOTLoad FirmwareOverview MOTLoad Implementation and Memory RequirementsMOTLoad Utility Applications MOTLoad TestsUsing MOTLoad Command Line InterfaceCommand Line Help Command Line RulesMOTLoad Command List MOTLoad CommandsCommand Description DownLoad ErrorDisplayNetBoot EchoCommand Description NetStats ResetNoCm PciDataRdMOTLoad Commands Default VME Settings MVME3100 vmeCfg -s -mMVME3100 vmeCfg -s -o1 Firmware Settings CR/CSR SettingsDisplaying VME Settings Editing VME Settings Deleting VME Settings Restoring Default VME SettingsRemote Start Slot Position CS/CSR Starting Address Alternate Boot Images and Safe Start Firmware Startup Sequence Following ResetFirmware Scan for Boot Image Address UsageValid Boot Images Checksum AlgorithmName Type Size MOTLoad Image Flags User ImagesMOTLoad Image Flags Name Value InterpretationAlternate Boot Data Structure MOTLoad Firmware Features MVME3100 Features SummaryFeature Description Functional DescriptionFunctional Description MVME721 RTM Features Summary Block Diagrams MVME3100 Block DiagramProcessor System MemoryLocal Bus Interface Control and Timers Logic I2C Serial Interface and DevicesFlash Memory Ethernet Interfaces Asynchronous Serial PortsPCI/PCI-X Interfaces and Devices MPC8540 PCI-X InterfaceTSi148 VME Controller Serial ATA Host ControllerPCI-X-to-PCI-X Bridges PCI Mezzanine Card SlotsGeneral-Purpose Timers Real-time Clock BatteryPMC Expansion Reset Control Logic Debug SupportPin Assignments Connectors PMC Expansion Connector J4PMC Expansion Connector J4 Pin Assignments Pin SignalPAR Ethernet Connectors GENET1/J41B, GENET2/J2B, ENET1/J2A Ethernet Connectors Pin AssignmentPin # Signal 1000 Mb/s 10/100 Mb/s PCI Mezzanine Card PMC Connectors J11 J14, J21 J23 PMC Slot 1 Connector J11 Pin AssignmentsPMC Slot 1 Connector J12 Pin Assignments PMC Slot 1 Connector J13 Pin Assignments PMC Slot 1 Connector J14 Pin Assignments PMC Slot 2 Connector J21 Pin Assignments PMC Slot 2 Connector J22 Pin Assignments PMC Slot 2 Connector J23 Pin Assignments Serial Port Connectors COM1/J41A, COM2-COM5/J2A-D 10. COM Port Connector Pin AssignmentsVMEbus P1 Connector 11. VMEbus P1 Connector Pin AssignmentsVMEbus P2 Connector 12. VME P2 Connector PinoutsPin P2-Z P2-A P2-B P2-C P2-D MVME721 PMC I/O Module PIM Connectors J10, J14 13. MVME721 Host I/O Connector J10 Pin AssignmentsPlanar sATA Power Connector J30 USB Connector J2714. Planar sATA Power Connector J30 Pin Assignments 15. USB Connector J27 Pin AssignmentsSATA Connectors J28 and J29 16. sATA Connectors J28 and J29 Pin AssignmentsHeaders Boundary Scan Header J24Processor COP Header J25 18. Processor COP Header J25 Pin AssignmentsPower Requirements Environmental SpecificationsModel Power Characteristics SpecificationsAppendix a Specifications Related Documentation Motorola Computer Group DocumentsTable B-1. Motorola Computer Group Documents Manufacturers’ Documents Table B-2. Manufacturers’ DocumentsDocument Title and Source Publication Number Table B-2. Manufacturers’ Documents Related Specifications Table B-3. Related SpecificationsIeee http//standards.ieee.org/catalog