Motorola MVME3100 manual CE Notice European Community

Page 5

!

Warning

CE Notice (European Community)

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Motorola products with the CE marking comply with the EMC Directive (89/336/EEC). Compliance with this directive implies conformity to the following European Norms:

EN55022 “Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment”; this product tested to Equipment Class A

EN55024 “Information technology equipment—Immunity characteristics—Limits and methods of measurement”

Board products are tested in a representative system to show compliance with the above mentioned requirements. A proper installation in a CE-marked system will maintain the required EMC performance.

In accordance with European Community directives, a “Declaration of Conformity” has been made and is available on request. Please contact your sales representative.

Image 5
Contents Installation and Use Page Safety Summary Flammability CE Notice European Community Limited and Restricted Rights Legend Contents Functional Description Specifications List of Figures List of Tables 13. MVME721 Host I/O Connector J10 Pin AssignmentsAbout This Manual Overview of ContentsConventions Used in This Manual Comments and SuggestionsIntroduction Hardware Preparation and InstallationDescription Getting StartedStartup Overview Overview of Startup ProceduresUnpacking Guidelines MVME3100 Layout Hardware ConfigurationMVME3100 Board Layout Setting Switch Pos OFF Factory Default Configuration Switch S4Configuration Switch S4 Settings Slot Geographical Address Settings Geographical Address Switch S3Geographical Address Switch Assignments RTM Seeprom Address Switch S1 PMC I/O Voltage ConfigurationRTM Eeprom Address Switch Assignments Function Not UsedInstalling the MVME3100 into a Chassis Hardware InstallationEeprom Address Settings Device Address A20MVME721 Rear Transition Module Connectors MVME3100 ConnectorsConnector Function Connection to PeripheralsCompleting the Installation Switches and Indicators Applying PowerFront-Panel LED Status Indicators Startup and OperationAdditional Onboard Status Indicators MVME721 LED Status IndicatorsGenet DS3 MOTLoad Firmware MOTLoad CommandsOverview MOTLoad Implementation and Memory RequirementsMOTLoad Tests MOTLoad Utility ApplicationsCommand Line Interface Using MOTLoadCommand Line Rules Command Line HelpMOTLoad Commands MOTLoad Command ListErrorDisplay Command Description DownLoadNetBoot EchoReset Command Description NetStatsNoCm PciDataRdMOTLoad Commands MVME3100 vmeCfg -s -m Default VME SettingsMVME3100 vmeCfg -s -o1 Displaying VME Settings Firmware SettingsCR/CSR Settings Editing VME Settings Remote Start Deleting VME SettingsRestoring Default VME Settings Slot Position CS/CSR Starting Address Firmware Startup Sequence Following Reset Alternate Boot Images and Safe StartAddress Usage Firmware Scan for Boot ImageName Type Size Valid Boot ImagesChecksum Algorithm User Images MOTLoad Image FlagsMOTLoad Image Flags Name Value InterpretationAlternate Boot Data Structure MOTLoad Firmware MVME3100 Features Summary FeaturesFeature Description Functional DescriptionFunctional Description MVME721 RTM Features Summary MVME3100 Block Diagram Block DiagramsLocal Bus Interface ProcessorSystem Memory Flash Memory Control and Timers LogicI2C Serial Interface and Devices Asynchronous Serial Ports Ethernet InterfacesMPC8540 PCI-X Interface PCI/PCI-X Interfaces and DevicesTSi148 VME Controller Serial ATA Host ControllerPCI Mezzanine Card Slots PCI-X-to-PCI-X BridgesPMC Expansion General-Purpose TimersReal-time Clock Battery Debug Support Reset Control LogicPin Assignments PMC Expansion Connector J4 ConnectorsPMC Expansion Connector J4 Pin Assignments Pin SignalPAR Pin # Signal 1000 Mb/s 10/100 Mb/s Ethernet Connectors GENET1/J41B, GENET2/J2B, ENET1/J2AEthernet Connectors Pin Assignment PMC Slot 1 Connector J11 Pin Assignments PCI Mezzanine Card PMC Connectors J11 J14, J21 J23PMC Slot 1 Connector J12 Pin Assignments PMC Slot 1 Connector J13 Pin Assignments PMC Slot 1 Connector J14 Pin Assignments PMC Slot 2 Connector J21 Pin Assignments PMC Slot 2 Connector J22 Pin Assignments PMC Slot 2 Connector J23 Pin Assignments 10. COM Port Connector Pin Assignments Serial Port Connectors COM1/J41A, COM2-COM5/J2A-D11. VMEbus P1 Connector Pin Assignments VMEbus P1 ConnectorPin P2-Z P2-A P2-B P2-C P2-D VMEbus P2 Connector12. VME P2 Connector Pinouts 13. MVME721 Host I/O Connector J10 Pin Assignments MVME721 PMC I/O Module PIM Connectors J10, J14USB Connector J27 Planar sATA Power Connector J3014. Planar sATA Power Connector J30 Pin Assignments 15. USB Connector J27 Pin Assignments16. sATA Connectors J28 and J29 Pin Assignments SATA Connectors J28 and J29Headers Boundary Scan Header J2418. Processor COP Header J25 Pin Assignments Processor COP Header J25Environmental Specifications Power RequirementsModel Power Characteristics SpecificationsAppendix a Specifications Table B-1. Motorola Computer Group Documents Related DocumentationMotorola Computer Group Documents Document Title and Source Publication Number Manufacturers’ DocumentsTable B-2. Manufacturers’ Documents Table B-2. Manufacturers’ Documents Ieee http//standards.ieee.org/catalog Related SpecificationsTable B-3. Related Specifications