Motorola MVME3100 manual Pin Assignments, Introduction

Page 58

Pin Assignments

5

Introduction

This chapter provides pin assignments for various connectors and headers on the MMVE3100 single-board computer and the MVME721 transition module.

■PMC Expansion Connector (J4)

■Ethernet Connectors (GENET1/J41B, GENET2/J2B, ENET1/J2A)

■PCI Mezzanine Card (PMC) Connectors (J11 – J14, J21 – J23)

■Serial Port Connectors (COM1/J41A, COM2–COM5/J2A-D)

■VMEbus P1 Connector

■VMEbus P2 Connector

■MVME721 PMC I/O Module (PIM) Connectors (J10, J14)

■Planar sATA Power Connector (J30)

■USB Connector (J27)

■sATA Connectors (J28 and J29)

The following headers are described in this chapter:

■Boundary Scan Header (J24)

■Processor COP Header (J25)

MVME3100 Installation and Use (V3100A/IH1)

47

Image 58

Contents Installation and Use Page Safety Summary Flammability CE Notice European Community Limited and Restricted Rights Legend Contents Functional Description Specifications List of Figures 13. MVME721 Host I/O Connector J10 Pin Assignments List of TablesOverview of Contents About This ManualComments and Suggestions Conventions Used in This ManualDescription Hardware Preparation and InstallationIntroduction Getting StartedUnpacking Guidelines Overview of Startup ProceduresStartup Overview Hardware Configuration MVME3100 LayoutMVME3100 Board Layout Configuration Switch S4 Settings Configuration Switch S4Setting Switch Pos OFF Factory Default Geographical Address Switch Assignments Geographical Address Switch S3Slot Geographical Address Settings RTM Eeprom Address Switch Assignments PMC I/O Voltage ConfigurationRTM Seeprom Address Switch S1 Function Not UsedEeprom Address Settings Hardware InstallationInstalling the MVME3100 into a Chassis Device Address A20Connector Function MVME3100 ConnectorsMVME721 Rear Transition Module Connectors Connection to PeripheralsCompleting the Installation Front-Panel LED Status Indicators Applying PowerSwitches and Indicators Startup and OperationMVME721 LED Status Indicators Additional Onboard Status IndicatorsGenet DS3 Overview MOTLoad CommandsMOTLoad Firmware MOTLoad Implementation and Memory RequirementsMOTLoad Utility Applications MOTLoad TestsUsing MOTLoad Command Line InterfaceCommand Line Help Command Line RulesMOTLoad Command List MOTLoad CommandsNetBoot Command Description DownLoadErrorDisplay EchoNoCm Command Description NetStatsReset PciDataRdMOTLoad Commands Default VME Settings MVME3100 vmeCfg -s -mMVME3100 vmeCfg -s -o1 CR/CSR Settings Firmware SettingsDisplaying VME Settings Editing VME Settings Restoring Default VME Settings Deleting VME SettingsRemote Start Slot Position CS/CSR Starting Address Alternate Boot Images and Safe Start Firmware Startup Sequence Following ResetFirmware Scan for Boot Image Address UsageChecksum Algorithm Valid Boot ImagesName Type Size MOTLoad Image Flags MOTLoad Image FlagsUser Images Name Value InterpretationAlternate Boot Data Structure MOTLoad Firmware Feature Description FeaturesMVME3100 Features Summary Functional DescriptionFunctional Description MVME721 RTM Features Summary Block Diagrams MVME3100 Block DiagramSystem Memory ProcessorLocal Bus Interface I2C Serial Interface and Devices Control and Timers LogicFlash Memory Ethernet Interfaces Asynchronous Serial PortsTSi148 VME Controller PCI/PCI-X Interfaces and DevicesMPC8540 PCI-X Interface Serial ATA Host ControllerPCI-X-to-PCI-X Bridges PCI Mezzanine Card SlotsReal-time Clock Battery General-Purpose TimersPMC Expansion Reset Control Logic Debug SupportPin Assignments PMC Expansion Connector J4 Pin Assignments ConnectorsPMC Expansion Connector J4 Pin SignalPAR Ethernet Connectors Pin Assignment Ethernet Connectors GENET1/J41B, GENET2/J2B, ENET1/J2APin # Signal 1000 Mb/s 10/100 Mb/s PCI Mezzanine Card PMC Connectors J11 J14, J21 J23 PMC Slot 1 Connector J11 Pin AssignmentsPMC Slot 1 Connector J12 Pin Assignments PMC Slot 1 Connector J13 Pin Assignments PMC Slot 1 Connector J14 Pin Assignments PMC Slot 2 Connector J21 Pin Assignments PMC Slot 2 Connector J22 Pin Assignments PMC Slot 2 Connector J23 Pin Assignments Serial Port Connectors COM1/J41A, COM2-COM5/J2A-D 10. COM Port Connector Pin AssignmentsVMEbus P1 Connector 11. VMEbus P1 Connector Pin Assignments12. VME P2 Connector Pinouts VMEbus P2 ConnectorPin P2-Z P2-A P2-B P2-C P2-D MVME721 PMC I/O Module PIM Connectors J10, J14 13. MVME721 Host I/O Connector J10 Pin Assignments14. Planar sATA Power Connector J30 Pin Assignments Planar sATA Power Connector J30USB Connector J27 15. USB Connector J27 Pin AssignmentsHeaders SATA Connectors J28 and J2916. sATA Connectors J28 and J29 Pin Assignments Boundary Scan Header J24Processor COP Header J25 18. Processor COP Header J25 Pin AssignmentsModel Power Power RequirementsEnvironmental Specifications Characteristics SpecificationsAppendix a Specifications Motorola Computer Group Documents Related DocumentationTable B-1. Motorola Computer Group Documents Table B-2. Manufacturers’ Documents Manufacturers’ DocumentsDocument Title and Source Publication Number Table B-2. Manufacturers’ Documents Table B-3. Related Specifications Related SpecificationsIeee http//standards.ieee.org/catalog