Motorola MVME6100 manual Getting Started, Hardware Preparation and Installation

Page 14

Chapter 1 Hardware Preparation and Installation

Note For maximum VMEbus performance, the MVME6100 should be mounted in a VME64x compatible backplane (5-row). 2eSST transfers are not supported when a 3-row backplane is used.

The MVME6100 supports multiple modes of I/O operation. By default, the board is configured for Ethernet port 2 to the front panel (non-specific transition module), and PMC slot 1 in IPMC mode. The board can be configured to route Ethernet port 2 to P2 and support MVME712M or MVME761 transition modules. The front/rear Ethernet and transition module options are configured by jumper block J30.

Selection of PMC slot 1 in PMC or IPMC mode is done by the jumper blocks J10, J15-J18, and J25-J28 (see Table 1-2 on page 5). IPMC mode is selected when an IPMC712 or IPMC761 module is used. If an IPMC is used, J30 should be configured for the appropriate transition module (see J30 configuration options as illustrated in Front/Rear Ethernet and Transition Module Options Header (J30) on page 8).

The IPMC712 and IPMC761 use AD11 as the IDSEL line for the Winbond PCI-ISA bridge device. This device supplies the four serial and one parallel port of the IPMC7xx module. The Discovery II PHB (MV64360) does not recognize address lines below AD16. For this reason, although an IPMC7xx module may be used on an MVME6100, the serial and parallel ports are not available, nor addressable. This issue will be resolved by MCG at a later date.

Note Other functions, such as Ethernet and SCSI interfaces, are function independent of the Winbond IDSEL line. The wide SCSI interface can only be supported through IPMC connector J3.

PMC mode is backwards compatible with the MVME5100 and MVME5500 and is accomplished by configuring the on-board jumpers.

Getting Started

This section provides an overview of the steps necessary to install and power up the MVME6100 and a brief section on unpacking and ESD precautions.

2MVME6100 Installation and Use (V6100A/IH2)

Image 14

Contents Installation and Use V6100A/IH2Trademarks Safety Summary Flammability Limited and Restricted Rights Legend Contents Functional Description Specifications List of Figures Gigabit Ethernet Connectors J9, J93 Pin Assignment List of TablesComments and Suggestions Overview of ContentsAbout This Manual Conventions Used in This Manual About This ManualDescription Hardware Preparation and InstallationIntroduction Hardware Preparation and Installation Getting StartedStartup Overview Overview of Startup ProceduresUnpacking Guidelines Hardware Configuration MVME6100 PreparationMVME6100 Jumper and Switch Settings Jumper Switch Function SettingsMVME6100 Layout Scon Header J7 PMC/IPMC Selection Headers J10, J15 J18, J25 J28No Srominit Srom Configuration Switch S3Srom Configuration Switch S3 Flash Boot Bank Select Configuration Switch S4 Positio FunctionConfiguration Switch S4 Hardware InstallationInstalling the MVME6100 into a Chassis Connector Function Completing the InstallationMVME6100 Connectors Connection to PeripheralsFront-Panel LED Status Indicators Applying PowerSwitches and Indicators Startup and OperationOverview MOTLoad CommandsMOTLoad Firmware MOTLoad Implementation and Memory RequirementsMOTLoad Utility Applications MOTLoad TestsUsing MOTLoad Command Line InterfaceCommand Line Help Command Line RulesCommand Description MOTLoad Command ListMOTLoad Commands MOTLoad Commands MOTLoad Commands MOTLoad Commands Default VME Settings MVME6100 vmeCfg -s -mMVME6100 vmeCfg -s -o1 Displaying VME Settings Firmware SettingsCR/CSR Settings Editing VME Settings VmeCfg -e -r40CRemote Start Deleting VME SettingsRestoring Default VME Settings Slot Position CS/CSR Starting Address Firmware Scan for Boot Image Alternate Boot Images and Safe StartFirmware Startup Sequence Following Reset Address Usage Name Type Size Valid Boot ImagesChecksum Algorithm MOTLoad Image Flags MOTLoad Image FlagsUser Images Name Value InterpretationAlternate Boot Data Structure Feature Description FeaturesMVME6100 Features Summary Functional DescriptionBlock Diagram MVME6100 Block DiagramSystem Controller ProcessorL3 Cache CPU Bus Interface Memory Controller InterfaceGigabit Ethernet MACs Device Controller InterfacePCI/PCI-X Interfaces Device Bus ParametersI2O Message Unit General-Purpose Timers/CountersWatchdog Timer Four Channel Independent DMA ControllerInterrupt Controller Flash Memory VMEbus InterfacePMCspan Interface System MemoryPCI Mezzanine Card Slots Idsel Routing Real-Time Clock/NVRAM/Watchdog TimerReset Control Logic Debug SupportPin Assignments PMC Expansion Connector J4 Pin Assignments ConnectorsPMC Expansion Connector J4 Pin SignalPAR Pin # Signal 1000 Mb/s 10/100 Mb/s Gigabit Ethernet Connectors J9, J93Gigabit Ethernet Connectors J9, J93 Pin Assignment PCI Mezzanine Card PMC Connectors J11 J14, J21 J24 PMC Slot 1 Connector J11 Pin AssignmentsPMC Slot 1 Connector J12 Pin Assignments PMC Slot 1 Connector J13 Pin Assignments PMC Slot 1 Connector J14 Pin Assignments PMC Slot 2 Connector J21 Pin Assignments PMC Slot 2 Connector J22 Pin Assignments PMC Slot 2 Connector J23 Pin Assignments 10. PMC Slot 2 Connector J24 Pin Assignments COM1 Connector J19 11. COM1 Connector J19 Pin AssignmentsVMEbus P1 Connector 12. VMEbus P1 Connector Pin AssignmentsVMEBus P2 Connector PMC Mode 13. VMEbus P2 Connector Pin Assignments PMC ModeP2IOGLAN1M Pin Row Z Row a Row B Row C Row D VMEbus P2 Connector Ipmc Mode14. VME P2 Connector Pinouts with IPMC712 15. VME P2 Connector Pinouts with IPMC761 Headers 16. Scon Header J7 Pin Assignments17. Boundary Scan Header J8 Pin Assignments 18. PMC/IPMC Configuration Jumper BlockBoundary Scan Header J8 COM2 Header J29 19. COM2 Planar Serial Port Header J29 Pin AssignmentsProcessor JTAG/COP Header J42 21. Processor JTAG/COP RISCWatch Header J42 Pin AssignmentsEnvironmental Specifications SpecificationsPower Requirements Supply Current RequirementsAppendix a Specifications Thermal Validation Thermally Significant ComponentsMeasurement Table B-1. Thermally Significant ComponentsMax. Allowable Component Reference Designator Generic Description Deg. C LocationFigure B-1. Thermally Significant Components-Primary Side Figure B-2. Thermally Significant Components-Secondary Side Measuring Case Temperature Component Temperature MeasurementMeasuring Junction Temperature PreparationFigure B-3. Mounting a Thermocouple Under a Heatsink Measuring Local Air Temperature Figure B-4. Measuring Local Air TemperatureRelated Documentation Motorola Embedded Communications Computing DocumentsDocument Title and Source Publication Number Manufacturers’ DocumentsTable C-2. Manufacturers’ Documents Related Specifications Table C-3. Related SpecificationsTable C-3. Related Specifications Index Index