Sony AR-B1474, DX4, 486DX Combination of ROM and RAM Disk, Installation D.O.C, Hardware Setting

Page 50

AR-B1474 User¡¦s Guide

5.4.5 Combination of ROM and RAM Disk

The AR-B1474 can be configured as a combination of one ROM disk and one RAM disk. Each disk occupies a drive unit.

Step 1: Use jumper block to select the proper ROM/RAM configuration you are going to use.

Step 2: Insert the first programmed EPROM into the socket mem1, the second into the socket MEM2, etc.

Step 3: Insert the SRAM chips starting from the first socket assigned as SRAM.

Step 4: Select the proper I/O base port, firmware address and disk drive number on SW1.

Step 5: Turn on power and boot DOS from hard disk drive or floppy disk drive.

Step 6: Use the DOS command [FORMAT] to format the RAM disk.

C:\>FORMAT [RAM disk letter] /U

Step 7: If 5V FLASH (small page) is being used for the first time.

And then use the DOS command [FORMAT] to format the FLASH disk.

Step 8: If large page 5V FLASH is being installed for the first time, please use the FLASH programming utility PGM1474.EXE to program ROM pattern files, which have been generated by RFG.EXE onto the FLASH chips.

NOTE: Users can only boot DOS from the ROM disk drive if the AR-B1474 is configured as a ROM and a RAM disk. You don’ t need to copy DOS onto the RAM disk.

5.5 INSTALLATION D.O.C.

5.5.1 Hardware Setting

(1) SSD BIOS Setting (JP7)

JP7 -- SSD BIOS

1

2

3

1

2

3

 

 

 

 

 

 

 

Disable Enable

Figure 5-12 JP7: SSD BIOS Setting

(2) D.O.C. Socket Select (M1)

DiskOnChip only use MEM1 socket, so user must set the M1 for adjusting the DiskOnChip’ s type.

A B C

1

2

3

M1

Figure 5-13 M1: D.O.C. Socket Select

5-12

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Industrial Grade 486DX/DX2/DX4 CPU Card Page Table of Contents Memory Banks & Programming RS-485 Bios ConsoleSpecifications Placement & Dimensions SSD Types Supported & IndexPreface Static Electricity Precautions OrganizationOverview IntroductionFeatures Packing ListKeyboard Controller System ControllerDMA Controller DMA ControllerInterrupt Controller Interrupt ControllerI/O Port Address Map 1 I/O Port Address MapHex Range Device Address Description TimerReal-Time Clock and Non-Volatile RAM Real-Time Clock & Non-Volatile RAMISA Bus Pin Assignment ISA Bus Pin AssignmentISA Bus Signal Description Name DescriptionTransmitter Holding Register THR Serial PortReceiver Buffer Register RBR DlabLine Control Register LCR Interrupt Enable Register IERInterrupt Identification Register IIR Modem Control Register MCRDivisor Latch LS, MS Parallel PortModem Status Register MSR Register AddressPrinter Control Latch & Printer Control Swapper Data SwapperPrinter Status Buffer Setting UP the System OverviewSerial Port System SettingRS-232 Connector DB1 & DB2 RS-485 Adapter Select JP3 & JP11HDD Pin Assignment Hard Disk IDE Connector CN1Power Connector J5 CN3 FDD Port Connector CN2Parallel Port Connector CN3 Pin PC/104 Connector Bus C & D CN4 6 PC/104 ConnectorPin PC/104 Connector Bus a & B CN6 PC/104 ISA Bus Signal Description IRQ 3-7, 9-12, 14CPU Voltage Select JP2 CPU SettingAMD DX2-80 CPU Select JP1 AMD 4X CPU 5x86 Select JP15CPU Clock Setting CPU Clock Select JP6 & JP9Cache RAM Size Select JP8 Memory SettingDram Configuration SIMM1Keyboard Connector LED Header J1, J2 & J4External Speaker Header J3 Reset Header J7Battery Setting CRT Display Type Select JP13Page Installation Utility Diskette PGM1474.EXEBU1474.EXE WD1474.EXEWP1474.EXE Display Error in PGF File Help to PGF FileWrite Protect Function Enable the Software Write ProtectDisable the Software Write Protect Hardware Write ProtectTime-Out Setting Watchdog TimerWatchdog Timer Setting Time Factor Time-Out Period SecondsWatchdog Timer Disabled Watchdog Timer EnabledWatchdog Timer Trigger Page Switch Setting Solid State DiskSSD Firmware Address Select SW1-3 & SW1-4 Overview2 I/O Port Address Select SW1-1 & SW1-2 DEVICE=C\DOS\EMM386.EXE X=C800-CFFFFlash Eprom Sram SSD Drive Number SW1-5 & SW1-6Simulate 2 Disk Drive ROM Type Select SW1-7 & SW1-8 Disk Drive Name ArrangementJumper Setting SSD Bios Select JP7Switch and Jumper Setting SSD Memory Type Setting M1 ~ M3 & JP5ROM Disk Installation UV Eprom 27CxxxUV Eprom 27CXXX Switch Setting Software Programming5V Large Flash 29FXXX Switch Setting Large Page 5V Flash Disk5V Flash 29CXXX & 28EEXXX Switch Setting Small Page 5V Flash ROM DiskUsing Tool Program Typing DOS CommandJumper Setting RAM DiskSSD Bios Setting JP7 Installation D.O.CHardware Setting Combination of ROM and RAM DiskSoftware Setting O.C. Setting SW1-8Page Bios Console Bios Setup OverviewFloppy Setup Standard Cmos SetupDate & Time Setup Hard Disk SetupAdvanced Cmos Setup Internal Cache Memory IDE Block Mode TransferIDE LBA Mode ShadowAdvanced Chipset Setup Power Management Auto Configuration with Optimal Setting Setting PasswordPassword Checking Auto Configuration with Fail Safe SettingExit Without Saving Bios ExitSave Settings and Exit CPU SpecificationsBios PCBPage Placement & Dimensions PlacementDimensions CS1 CS0 Using Memory BankMemory Banks & Programming RS-485 SocketSend out one character Transmit Programming RS-485Initialize COM port Receive data Send out one character to COM1Page SSD Types Supported & Index SSD Types Supported10-2 Index Name Function

DX4, AR-B1474, 486DX specifications

The Sony 486DX, AR-B1474, and DX4 are notable examples of advanced computing technologies from the early to mid-1990s, a time when personal computers were rapidly evolving to meet increasing user demands. These systems played a pivotal role in shaping the landscape of modern computing.

The Sony 486DX is built around the popular Intel 80486 microprocessor, which was a significant step up from its predecessor, the 386. The 486DX featured a 32-bit architecture and introduced integrated cache memory, which greatly enhanced data processing speeds and overall system performance. Operating at clock speeds typically ranging from 25 to 100 MHz, the 486DX models provided a solid foundation for running more sophisticated software applications and advanced games of the era.

Accompanying the 486DX was the AR-B1474 motherboard, designed to maximize the potential of the 486 architecture. This motherboard featured support for up to 512 KB of level 2 cache memory, further boosting performance for data-heavy tasks. The AR-B1474 also included extensive connectivity options, with ISA slots for legacy devices, as well as support for EISA, making it compatible with a wide range of hardware peripherals. This versatility made the AR-B1474 a popular choice among builders of custom desktop PCs during its time.

The DX4, another significant milestone, built upon the 486 architecture by introducing a clock-doubling technique. By effectively allowing the processor to perform operations at up to three times its base clock speed (typically 75 or 100 MHz), the DX4 could handle even more demanding applications, thereby providing users with significant performance improvements without requiring a complete overhaul of their systems.

Both the 486DX and DX4 processors facilitated advancements in multimedia capabilities, with improved graphics rendering and audio performance that supported CD-ROMs and early gaming technologies. This made them particularly appealing to consumers looking for a versatile machine for both work and entertainment.

Overall, the combination of the Sony 486DX, AR-B1474 motherboard, and DX4 processor exemplifies a significant chapter in computing history, showcasing how hardware advancements seamlessly integrated with user needs for performance and flexibility. As these technologies laid the groundwork for future innovations, they remain noteworthy for their contributions to the evolution of personal computing.
Top Page Image Contents