Sony 486DX, DX4, AR-B1474 manual Installation, Overview

Page 31

AR-B1474 User¡¦s Guide

4. INSTALLATION

This chapter describes the procedure of the installation. The following topics are covered:

•Overview

•Utility Diskette

•Write Protect Function

•Watchdog Timer

4.1OVERVIEW

This chapter provides information for you to set up a working system based on the AR-B1474 CPU card. Please read the details of the CPU card’ s hardware descriptions before installation carefully, especially jumpers setting, switch setting and cable connection.

Follow steps listed below for proper installation:

Step 1 : Read the CPU card’ s hardware description in this manual.

Step 2 : Install any DRAM SIMM onto the CPU card.

Step 3: Install the EPROMs, FLASHs ro SRAMs on the memory sockets.

Step 4 : Set jumpers and switch.

Step 5 : Make sure that the power supply connected to your passive CPU board is turned off.

Step 6 : Plug the CPU card into a free AT-bus slot or PICMG slot on the backplane and secure it in place with a screw to the system chassis.

Step 7 : Connect all necessary cables. Make sure that the FDC, HDC, serial and parallel cables are connected to pin 1 of the related connector.

Step 8 : Connect the hard disk/floppy disk flat cables from the CPU board to the drives. Connect a power source to each drive.

Step 9 : Install a MDA, CGA, EGA or VGA display card in your system.

Step 10 : Plug the keyboard into the keyboard connector.

Step 11 : Turn on the power.

Step 12: Configure your system with the BIOS Setup program then re-boot your system.

Step 13: If the CPU card does not work, turn off the power and read the hardware description carefully again.

Step 14: If the CPU card still does not perform properly, return the card to your dealer for immediate service.

4-1

Image 31

Contents Industrial Grade 486DX/DX2/DX4 CPU Card Page Table of Contents SSD Types Supported & Index Bios ConsoleSpecifications Placement & Dimensions Memory Banks & Programming RS-485Preface Organization Static Electricity PrecautionsIntroduction OverviewPacking List FeaturesDMA Controller System ControllerDMA Controller Keyboard ControllerInterrupt Controller Interrupt ControllerHex Range Device 1 I/O Port Address MapI/O Port Address Map Real-Time Clock & Non-Volatile RAM TimerReal-Time Clock and Non-Volatile RAM Address DescriptionISA Bus Pin Assignment ISA Bus Pin AssignmentName Description ISA Bus Signal DescriptionDlab Serial PortReceiver Buffer Register RBR Transmitter Holding Register THRModem Control Register MCR Interrupt Enable Register IERInterrupt Identification Register IIR Line Control Register LCRRegister Address Parallel PortModem Status Register MSR Divisor Latch LS, MSPrinter Status Buffer Data SwapperPrinter Control Latch & Printer Control Swapper Overview Setting UP the SystemRS-485 Adapter Select JP3 & JP11 System SettingRS-232 Connector DB1 & DB2 Serial PortPower Connector J5 Hard Disk IDE Connector CN1HDD Pin Assignment Parallel Port Connector CN3 FDD Port Connector CN2CN3 Pin PC/104 Connector Bus a & B CN6 6 PC/104 ConnectorPin PC/104 Connector Bus C & D CN4 IRQ 3-7, 9-12, 14 PC/104 ISA Bus Signal DescriptionAMD 4X CPU 5x86 Select JP15 CPU SettingAMD DX2-80 CPU Select JP1 CPU Voltage Select JP2CPU Clock Select JP6 & JP9 CPU Clock SettingSIMM1 Memory SettingDram Configuration Cache RAM Size Select JP8 LED Header J1, J2 & J4 Keyboard ConnectorCRT Display Type Select JP13 Reset Header J7Battery Setting External Speaker Header J3Page Installation PGM1474.EXE Utility DisketteWP1474.EXE WD1474.EXEBU1474.EXE Help to PGF File Display Error in PGF FileHardware Write Protect Enable the Software Write ProtectDisable the Software Write Protect Write Protect FunctionTime Factor Time-Out Period Seconds Watchdog TimerWatchdog Timer Setting Time-Out SettingWatchdog Timer Trigger Watchdog Timer EnabledWatchdog Timer Disabled Page Solid State Disk Switch SettingDEVICE=C\DOS\EMM386.EXE X=C800-CFFF Overview2 I/O Port Address Select SW1-1 & SW1-2 SSD Firmware Address Select SW1-3 & SW1-4Simulate 2 Disk Drive SSD Drive Number SW1-5 & SW1-6Flash Eprom Sram Disk Drive Name Arrangement ROM Type Select SW1-7 & SW1-8SSD Bios Select JP7 Jumper SettingUV Eprom 27Cxxx SSD Memory Type Setting M1 ~ M3 & JP5ROM Disk Installation Switch and Jumper SettingSoftware Programming UV Eprom 27CXXX Switch SettingLarge Page 5V Flash Disk 5V Large Flash 29FXXX Switch SettingSmall Page 5V Flash ROM Disk 5V Flash 29CXXX & 28EEXXX Switch SettingTyping DOS Command Using Tool ProgramRAM Disk Jumper SettingCombination of ROM and RAM Disk Installation D.O.CHardware Setting SSD Bios Setting JP7O.C. Setting SW1-8 Software SettingPage Bios Setup Overview Bios ConsoleHard Disk Setup Standard Cmos SetupDate & Time Setup Floppy SetupAdvanced Cmos Setup Shadow IDE Block Mode TransferIDE LBA Mode Internal Cache MemoryAdvanced Chipset Setup Power Management Auto Configuration with Fail Safe Setting Setting PasswordPassword Checking Auto Configuration with Optimal SettingSave Settings and Exit Bios ExitExit Without Saving PCB SpecificationsBios CPUPage Placement Placement & DimensionsDimensions Socket Using Memory BankMemory Banks & Programming RS-485 CS1 CS0Initialize COM port Programming RS-485Send out one character Transmit Send out one character to COM1 Receive dataPage SSD Types Supported SSD Types Supported & Index10-2 Name Function Index