Sony AR-B1474, DX4 SSD Memory Type Setting M1 ~ M3 & JP5, ROM Disk Installation, UV Eprom 27Cxxx

Page 44

AR-B1474 User¡¦s Guide

5.3.2 SSD Memory Type Setting (M1 ~ M3 & JP5)

A B C

1

2

3 M1, M2 & M3

A B C

1

2

3 M1, M2 & M3

A B C

1

2

3 M1, M2 & M3

A B C

1

2

3 M1, M2 & M3

JP5

1 2 3

1MX8 EPROM (Only)

JP5

1 2 3

EPROM (128KX8, 256KX8 and 512KX8)

5V FLASH (64KX8, 128KX8 and 256KX8)

(Factory Preset)

JP5

1 2 3

5V FLASH (512KX8 Only)

JP5

1 2 3

SRAM

Figure 5-4 M1~M3 & JP5: Memory Type Setting

5.4 ROM DISK INSTALLATION

The section describes the various type SSDs’ installation steps as follows. The jumper and switch adjust as SSD’ s different type to set.

5.4.1 UV EPROM (27Cxxx)

(2) Switch and Jumper Setting

Step 1: Use jumper block to set the memory type as ROM (FLASH).

Step 2: Select the proper I/O base port, firmware address, disk drive number and EPROM type on SW1.

Step 3: Insert programmed EPROM(s) or FLASH(s) chips into sockets starting at MEM1.

5-6

Image 44

Contents Industrial Grade 486DX/DX2/DX4 CPU Card Page Table of Contents Bios Console Specifications Placement & DimensionsMemory Banks & Programming RS-485 SSD Types Supported & IndexPreface Static Electricity Precautions OrganizationOverview IntroductionFeatures Packing ListSystem Controller DMA ControllerKeyboard Controller DMA ControllerInterrupt Controller Interrupt ControllerI/O Port Address Map 1 I/O Port Address MapHex Range Device Timer Real-Time Clock and Non-Volatile RAMAddress Description Real-Time Clock & Non-Volatile RAMISA Bus Pin Assignment ISA Bus Pin AssignmentISA Bus Signal Description Name DescriptionSerial Port Receiver Buffer Register RBRTransmitter Holding Register THR DlabInterrupt Enable Register IER Interrupt Identification Register IIRLine Control Register LCR Modem Control Register MCRParallel Port Modem Status Register MSRDivisor Latch LS, MS Register AddressPrinter Control Latch & Printer Control Swapper Data SwapperPrinter Status Buffer Setting UP the System OverviewSystem Setting RS-232 Connector DB1 & DB2Serial Port RS-485 Adapter Select JP3 & JP11HDD Pin Assignment Hard Disk IDE Connector CN1Power Connector J5 CN3 FDD Port Connector CN2Parallel Port Connector CN3 Pin PC/104 Connector Bus C & D CN4 6 PC/104 ConnectorPin PC/104 Connector Bus a & B CN6 PC/104 ISA Bus Signal Description IRQ 3-7, 9-12, 14CPU Setting AMD DX2-80 CPU Select JP1CPU Voltage Select JP2 AMD 4X CPU 5x86 Select JP15CPU Clock Setting CPU Clock Select JP6 & JP9Memory Setting Dram ConfigurationCache RAM Size Select JP8 SIMM1Keyboard Connector LED Header J1, J2 & J4Reset Header J7 Battery SettingExternal Speaker Header J3 CRT Display Type Select JP13Page Installation Utility Diskette PGM1474.EXEBU1474.EXE WD1474.EXEWP1474.EXE Display Error in PGF File Help to PGF FileEnable the Software Write Protect Disable the Software Write ProtectWrite Protect Function Hardware Write ProtectWatchdog Timer Watchdog Timer SettingTime-Out Setting Time Factor Time-Out Period SecondsWatchdog Timer Disabled Watchdog Timer EnabledWatchdog Timer Trigger Page Switch Setting Solid State DiskOverview 2 I/O Port Address Select SW1-1 & SW1-2SSD Firmware Address Select SW1-3 & SW1-4 DEVICE=C\DOS\EMM386.EXE X=C800-CFFF Flash Eprom Sram SSD Drive Number SW1-5 & SW1-6 Simulate 2 Disk Drive ROM Type Select SW1-7 & SW1-8 Disk Drive Name ArrangementJumper Setting SSD Bios Select JP7SSD Memory Type Setting M1 ~ M3 & JP5 ROM Disk InstallationSwitch and Jumper Setting UV Eprom 27CxxxUV Eprom 27CXXX Switch Setting Software Programming5V Large Flash 29FXXX Switch Setting Large Page 5V Flash Disk5V Flash 29CXXX & 28EEXXX Switch Setting Small Page 5V Flash ROM DiskUsing Tool Program Typing DOS CommandJumper Setting RAM DiskInstallation D.O.C Hardware SettingSSD Bios Setting JP7 Combination of ROM and RAM DiskSoftware Setting O.C. Setting SW1-8Page Bios Console Bios Setup OverviewStandard Cmos Setup Date & Time SetupFloppy Setup Hard Disk SetupAdvanced Cmos Setup IDE Block Mode Transfer IDE LBA ModeInternal Cache Memory ShadowAdvanced Chipset Setup Power Management Setting Password Password CheckingAuto Configuration with Optimal Setting Auto Configuration with Fail Safe SettingExit Without Saving Bios ExitSave Settings and Exit Specifications BiosCPU PCBPage Placement & Dimensions PlacementDimensions Using Memory Bank Memory Banks & Programming RS-485CS1 CS0 SocketSend out one character Transmit Programming RS-485Initialize COM port Receive data Send out one character to COM1Page SSD Types Supported & Index SSD Types Supported10-2 Index Name Function