8e6 Technologies MSA-004-005 quick start Physically Connect the ProxyBlocker to the Network

Page 40

B.At the Location pull-down menu, select the time zone for the specified region.

If necessary, select a language set from the Language pull-down menu to display that text in the console.

C.Click Apply to apply your settings, and to reboot the ProxyBlocker.

Physically Connect the ProxyBlocker to the Network

Once your ProxyBlocker network parameters are set, you must physically connect the unit to your network. This step requires two standard CAT-5E cables.

NOTE: This section requires you to restart the ProxyBlocker. If you wish to relocate the ProxyBlocker before connecting it to the network, you must first shut down the server instead of restarting it. To shut down the ProxyBlocker, go to the navigation panel, click Control, and then select ShutDown. Once the server is shut down, you must power on the ProxyBlocker and then log back into the Administra- tor console.

A.Restart the server using the steps defined below (i-iii). These steps must always be performed when restarting the ProxyBlocker. Never reset the server by using the power or reset buttons.

i.From the navigation panel of the System section of the console, click Control and select Reboot from the pop-up menu to display the Reboot window.

ii.Click the Reboot button.

iii.From the time you click Reboot, you have approximately 2 minutes to perform sub-steps B through E while the ProxyBlocker goes through the reboot process.

B.Disconnect the crossover cable from the ProxyBlocker.

C.Plug one end of a standard CAT-5E cable into the ProxyBlocker’s LAN 1 port.

D.Plug the other end of the CAT-5E cable into an open port on the network hub that handles the Internet traffic you wish to filter.

E.Repeat sub-steps B and C for the ProxyBlocker’s LAN 2 port.

F.Wait until the reboot process has completed, indicated by the drive light staying off for 30 seconds. This process may take 5 to 10 minutes. Proceed to Step 2.

NOTES: If you receive a connection failure message during the reboot process, please disregard it, as this often occurs when there is a change in the IP address.

To restart the browser window, close both the ProxyBlocker Administrator console and the ProxyBlocker Introductory Window. Begin a new session by opening a new browser window and then logging back into the Administrator console.

36

8e6 ProxyBlocker Quick Start Guide

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Guide 8e6 ProxyBlocker Quick Start Guide Contents 8e 6 Proxy Blocker Quick Start Guide 8e6 ProxyBlocker Introduction About this Document Conventions Used in this Document8e6 Corporate Headquarters USA Procedures8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Setup Precautions Rack Mount the ServerOptional Install the Chassis Rails Rack Mount Instructions8e6 ProxyBlocker Quick Start Guide Optional Install the Traditional UP Racks 8e6 ProxyBlocker Quick Start Guide Optional Install the Open Racks 8e6 ProxyBlocker Quick Start Guide 8e6 ProxyBlocker Quick Start Guide Install the Chassis into the Rack Check the Power Supply Power Supply PrecautionsGeneral Safety Information Server Operation and Maintenance PrecautionsAC Power Cord and Cable Precautions Electrical Safety PrecautionsMotherboard Battery Precautions Wizard Setup Requirements Setup ProceduresAdministrator Console Setup Requirements Wizard Setup Procedures Monitor and Keyboard SetupSerial Console Setup Link the Workstation to the ProxyBlockerHyperTerminal Setup Procedures 8e6 ProxyBlocker Quick Start Guide 8e6 ProxyBlocker Quick Start Guide Login screen System Configuration ScreenSystem Configuration Administration menu System Status Screen Log Off, Disconnect the PeripheralsPreliminary Setup Console Setup ProceduresWorkstation Configurations Boot Up Process Network Setup Access the ProxyBlocker Administrator ConsoleLog in to ProxyBlocker Administrator Console Network Network Operation Mode Network LAN Settings Network NTP Servers Network Regional Setting Physically Connect the ProxyBlocker to the Network Test the ProxyBlocker Console Connection Test Filtering Set Library UpdatesActivate and Register the ProxyBlocker Perform a Complete Library Update Monitor the Library Update Process Conclusion LED Indicator Color Condition Description LED Indicator Key Button KeyMSA Units Safety Compliance Declaration of the Manufacturer or ImporterElectromagnetic Compatibility EMC Electromagnetic Compatibility Class a NoticeEC Declaration of Conformity Index Wizard setup 19 8e6 ProxyBlocker Quick Start Guide
Top Page Image Contents