McQuay Micro Tech Open Protocol Driver Manual | Page 33 of 35 |
Appendix B. Error Messages
Those messages marked with an * are only printed once even if they occur repeatedly.
Error Message | Action | |
McQuay:#1 FYI. The MapDesc | The length of the Map Descriptor used to expose driver statistics is | |
too short. Set the length to at least 1000. You can ignore this | ||
called <%s> is too short | ||
message – the driver will abandon excess statistics. | ||
| ||
McQuay:#2 FYI. You could | You can safely ignore this message. It is a prompt. Refer to | |
have used a MapDesc called | ||
Appendix A.8. | ||
<%s> to expose diagnostic info. | ||
McQuay:#3 FYI. Normally | This is a reminder that a password is expected when a node is | |
defined. Refer to sections 4.3 or 5.2. Even though password | ||
passwords are defined for each | ||
node. | checking is not enforced when the driver is configured as a Server, | |
the driver expects one to be defined for every node. | ||
| ||
McQuay:#4 Err. Node list if full. | A maximum of 100 McQuay device nodes can be configured per | |
Max=%d | FieldServer. If the limit is reached, call support. | |
| A node has been provided with two passwords. This is either a | |
| configuration error or two nodes with the same address are | |
McQuay:#5 Err. Node=%d has | connected to different ports. The driver can only store one password | |
more than one password. | per node address and cannot use the port number to differentiate | |
| them. | |
| if they have the same addresses. | |
*McQuay:#9 FYI. Device | Device Scaling is being applied and the driver doesn’t know how to | |
scale a variable. Please submit your configuration file with your | ||
scaling method unknown. | ||
request for support. | ||
| ||
McQuay:#10 Err. Node=%s. | The driver doesn’t recognize the equipment type specified using the | |
PLC_Type parameter in the configuration file. Refer to Appendix A.3 | ||
Equip. type not recognized. | ||
for a list of valid equipment types.10 | ||
McQuay:#11 Err. Node=%s. | Refer to Sections 4.3, 5.2. and Appendix A.310 | |
Equip. Type not specified. |
| |
McQuay:#13 Err. | Refer to Appendix A.2 for a list of valid field names. Refer also to | |
MapDesc=%s. Field Name | ||
Sections 4.4 or 5.3. | ||
unknown. | ||
| ||
McQuay:#14 Err. | Corrective action is required. When writing to a McQuay device using | |
MapDesc=%s. Max Len=1 for | ||
direct addressing the length may only be 110 | ||
Writes with direct addr. |
| |
McQuay:#15 Err. | Neither a field name nor an address was specified. The driver does | |
MapDesc=%s. Field | not know what location to read. Specify a field name from Appendix | |
Name/Address Required. | A.2.10 | |
McQuay:#16 Err. | Each Map Descriptor must be connected to a node. This is done by | |
MapDesc=%s. No Node. | specifying a node name. 10 | |
McQuay:#17 Err. | The offset added to the length of the Map Descriptor extends beyond | |
MapDesc=%s. Md too short. | the Data Array. Increase the Data Array length. 10 | |
McQuay:#18 Err. | When using ‘everything’ as a field name the Map Descriptor function | |
MapDesc=%s. Cannot write | ||
must be Rdbc or Rdb as this is a read only function.10 | ||
'Everything'. |
| |
McQuay:#19 do diagnostic 3 | Call FieldServer Technical Support. A developer diagnostic has been | |
McQuay:#20 do diagnostic 1 | ||
called and should not have been. | ||
McQuay:#21 do diagnostic 2 | ||
|
10Correct the configuration by editing the CSV file and downloading it to the FieldServer, then reset the FieldServer for the changes to take effect.
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldServer.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldServer.com