McQuay Micro Tech Open Protocol Driver Manual | Page 34 of 35 | |||
|
|
|
|
|
| Error Message | Action |
|
|
| McQuay:#22 Err. Illegal | Check configuration file, a Node_ID is out of range. 11 |
| |
| Node_ID [%d] - Set to 1 |
|
|
|
|
| If the Node_ID is greater than 255 then this message is printed. In |
| |
|
| versions of the driver prior to 1.02 this was permitted and these |
| |
| McQuay:#23 FYI. Config | configurations will operate correctly. In versions since 1.02a the route |
| |
| parameter is used to provide the routing device’s address. Convert |
| ||
| requires |
| ||
| the Node_ID as follows. Divide the old Node_ID by 256. Set the |
| ||
| Read Manual. |
| ||
| Node_ID equal to remainder and set the route equal to the quotient. |
| ||
|
|
| ||
|
| Example; Old Node_ID = 834. | 834 div 256 = 3 remainder 66. |
|
|
| Therefore Route=3 and Node_ID=66. |
| |
| McQuay:#24 Err. Illegal | If the Node_ID is > 255 and the Route is specified too then this error |
| |
| is printed. The Node_ID should be a number in the range 0 to |
| ||
| Node_ID/Route |
| ||
| 255.Error! Bookmark not defined. |
| ||
|
|
| ||
| McQuay:#25 Err. Max Len=1 | The length parameter must be set to 1 when a Map Descriptor has |
| |
| when Bytes_Per_Field > 1. |
| ||
| the Bytes_Per_Field parameter specified10 |
| ||
| MD=%s. |
|
|
|
| McQuay:#26 Err. Max | Legal values for the Bytes_Per_Field parameter are whole numbers |
| |
| Bytes_Per_Field=4. MD=%s. | in the range 1 to 4 inclusive. 10 |
|
|
|
| This message is printed if a NAK response is received in the first few |
| |
| McQuay:#27* Err. | polls to a node. The driver guesses that the reason is that the |
| |
| Response=NAK. Read Manual. | Node_ID/route or password has been incorrectly specified in the |
| |
| Maybe password or Node_ID | configuration file. Verify these settings. The message is printed once |
| |
|
| and suppressed for subsequent occurrences. Refer to Appendix C.2 |
| |
|
| The message is printed and then suppressed for subsequent |
| |
|
| occurrences, but the NAK stat is incremented for each occurrence. |
| |
|
| The driver is reporting that the McQuay device responded with a NAK |
| |
| McQuay:#28* Err. Device | under different circumstances from msg#27 which is printed if the |
| |
| NAK is received during the first few polls. The message indicates that |
| ||
| responded with a NAK. |
| ||
| the McQuay device could not respond. If the NAK's are occasional, |
| ||
|
|
| ||
|
| assume that noise has corrupted an occasional message. If they |
| |
|
| occur frequently assume a systematic or connection error. Refer to |
| |
|
| Error! Reference source not found. and Appendix C.2. |
| |
11Correct the configuration by editing the CSV file and downloading it to the FieldServer, then reset the FieldServer for the changes to take effect.
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldServer.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldServer.com