Maxtor 90750D3, 91024D4, 91280D5, 91536D6, 91792D7 Physical Dimensions, Parameter Standard Metric

Page 19

PRODUCTSPECIFICATIONS

Physical Dimensions

PARAMETER	STANDARD		METRIC
H eig ht	1.0 2	inches	2 5 .9	m illim eters
L eng th	5 .7 8	inches	1 4 6 .6	m illim eters
W idth	4 .0 0	inche s	10 2 .1	m illim eters
W eight	1.3 poun ds		0 .5 9	kilog ram s

1.028 max

[25.9 mm]


	6 x 6-32			1.638 ± .005		1.122 ± .02


	UNC Tap			[41.61 mm]		[28.4 mm]

4.000 ± .01

[101.6 mm]

5.787 max

[146.6 mm]

4 x 6-32

1.75 ± .02

1.625 ± .02

UNC Tap

.25 ± .01

4.00 ± .01

[102.1 mm]

3.75± .01 [95.25 mm]

Figure 3 - 1

Outline and Mounting Dimensions

3 – 2

Image 19

Contents HA RD Drive Produc T MA Nual DiamondMax Plus Revisions Manual No U T I O N Before You BeginContents Handling and Installation Product SpecificationsHost Software Interface AT Interface DescriptionService and Support Interface CommandsGlossary Figures Abbreviations IntroductionMaxtor Corporation Manual OrganizationNumbering Signal ConventionsConventions Key WordsProduct Description DiamondMax Plus 5120 Key FeaturesFunctional / Interface Product FeaturesSoftware ECC Correction On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Defect Management Zone DMZAutomatic Write Reallocation AWR Read-Ahead ModeCache Management Buffer SegmentationMajor HDA Components Dual Drive Support Subsystem ConfigurationJumper Location/Configuration Cylinder LimitationModels and Capacities Product SpecificationsDrive Configuration Performance SpecificationsParameter Standard Metric Physical DimensionsEnvironmental Limits Power RequirementsPower Mode Definitions EPA Energy Star ComplianceShock and Vibration Reliability SpecificationsRadiated Electromagnetic Field Emissions EMC Compliance Safety Regulatory ComplianceCanadian Emissions Statement Important Notice Handling and InstallationHard Drive Handling Precautions Pre-formatted DriveMulti-pack Shipping Container Unpacking and InspectionRecommended Mounting Configuration Physical InstallationRepacking Before You Begin General Requirements Mounting Drive in System Attaching Interface Power Cables System Setup Hard Drive Preparation System Hangs During Boot Pin Description Summary Interface ConnectorSignal AT Interface DescriptionPin Description Table PIN Name Signal Name Signal DescriptionPIO Timing Timing Parameters ModeDMA Timing Timing Parameters all times in nanoseconds Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Task File Registers Error RegisterFeatures Register Host Software InterfaceDevice/Head Register Sector Count RegisterSector Number Register Cylinder Number RegistersCommand Register Summary Command Name Command Code Parameters Used SDHDigital Input Register Control Diagnostic RegistersAlternate Status Register Device Control RegisterReset Handling Reset and Interrupt HandlingInterrupt Handling Set Feature Commands Interface CommandsRead Sectors Read CommandsRead Verify Sectors Read Multiple Read DMAWrite Verify Sectors Write CommandsSet Multiple Mode Write SectorsWrite DMA Write MultipleSet Features Mode Set Feature CommandsPower Mode Commands Sleep Mode Identify Drive Initialization Commands15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Execute Drive Diagnostic Seek, Format and Diagnostic CommandsFormat Track Execute S.M.A.R.T A.R.T. Command SetSupport Service and SupportService Policy No Quibble ServiceCustomer Service MaxFax ServiceInternet Glossary Error Free Direct AccessDirect Memory Access Error Correction Code ECCFlux Changes PER Inch Hard ErrorHead Disk Assembly HDA File Allocation Table FATLogical Sector Phase Locked Loop PLLLogical Address Logical Block AddressingSector Pulse Signal Random Access Memory RAMRead Gate Signal Recoverable ErrorTHIN-FILM Media UN-CORRECTABLE ErrorUnrecoverable Error Write Gate Signal