Maxtor 92048D8, 91024D4, 90750D3 Handling and Installation, Pre-formatted Drive, Important Notice

Page 23

INSTALLATION

SECTION 4

Handling and Installation

Pre-formatted Drive

This Maxtor hard drive has been formatted at the factory. Do not use a low-level formatting program.

Important Notice

There are a number of system BIOS’s currently in use which do not support hard drives with more than 4095 cylinders (2.1 gigabytes). This section contains information describing the conditions which may identify this limitation. In order to obtain the full capacity of your Maxtor drive, you will need to follow the recommended installation instructions.

Hard Drive Handling Precautions

◆During handling, NEVER drop, jar, or bump a drive. Handle the drive by its sides and avoid touching the printed circuit board assembly (PCBA).

◆Hard drives are sensitive to electrostatic discharge (ESD) damage. Use proper ESD practices by grounding yourself and the computer system the hard drive will be installed in.

◆Allow the hard drive to reach room temperature BEFORE installing it in your computer system.

◆NEVER switch DC power onto the drive NEVER connect a live connector to the

by plugging an electrically live DC source cable into the drive's connector. hard drive's IDE interface connector.

Electro-Static Discharge (ESD)

To avoid some of the problems associated with ESD, Maxtor advises that anyone handling a disk drive use a wrist strap with an attached wire connected to an earth ground. Failure to observe these precautions voids the product warranty.

Manufacturers frequently experience “unsolved” component/hardware malfunctions often caused by ESD. To reduce the incidence of ESD-related problems, Maxtor recommends that any electronics manufacturing plans include a comprehensive ESD program, the basic elements and functions of which are outlined here:

ESD Program Element

ESD Program Function

Management

Institute and maintain

Chief coordinator

Organize and enforce

Multi-department committee

Evaluate and improve

Employee training

Educate and inform

ESD program supplies typically include: wrist- and foot-worn grounding straps; counter-top and floor antistatic matting; wrist strap testers; ESD video and training materials. Sources for such supplies include:

Static Control Systems – 3M

Charleswater

225-4S, 3M Center

93 Border St.

St. Paul, MN 55144

West Newton, MA 02165-9990

Maxtor also offers a complete video training package, “Care and Handling of Maxtor Disk Drives.” Contact your Maxtor representative for details.

4 – 12

Page 22 Page 24
Image 23
Page 22 Page 24
Contents HA RD Drive Produc T MA Nual DiamondMax Plus Revisions Manual No U T I O N Before You BeginContents Handling and Installation Product SpecificationsHost Software Interface AT Interface DescriptionGlossary Interface CommandsService and Support Figures Abbreviations IntroductionMaxtor Corporation Manual OrganizationNumbering Signal ConventionsConventions Key WordsProduct Description DiamondMax Plus 5120 Key FeaturesFunctional / Interface Product FeaturesSoftware ECC Correction On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Defect Management Zone DMZAutomatic Write Reallocation AWR Read-Ahead ModeCache Management Buffer SegmentationMajor HDA Components Dual Drive Support Subsystem ConfigurationJumper Location/Configuration Cylinder LimitationModels and Capacities Product SpecificationsDrive Configuration Performance SpecificationsParameter Standard Metric Physical DimensionsEnvironmental Limits Power RequirementsPower Mode Definitions EPA Energy Star ComplianceShock and Vibration Reliability SpecificationsCanadian Emissions Statement Safety Regulatory ComplianceRadiated Electromagnetic Field Emissions EMC Compliance Important Notice Handling and InstallationHard Drive Handling Precautions Pre-formatted DriveMulti-pack Shipping Container Unpacking and InspectionRepacking Physical InstallationRecommended Mounting Configuration Before You Begin General Requirements Mounting Drive in System Attaching Interface Power Cables System Setup Hard Drive Preparation System Hangs During Boot Pin Description Summary Interface ConnectorSignal AT Interface DescriptionPin Description Table PIN Name Signal Name Signal DescriptionPIO Timing Timing Parameters ModeDMA Timing Timing Parameters all times in nanoseconds Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Task File Registers Error RegisterFeatures Register Host Software InterfaceDevice/Head Register Sector Count RegisterSector Number Register Cylinder Number RegistersCommand Register Summary Command Name Command Code Parameters Used SDHDigital Input Register Control Diagnostic RegistersAlternate Status Register Device Control RegisterInterrupt Handling Reset and Interrupt HandlingReset Handling Set Feature Commands Interface CommandsRead Verify Sectors Read CommandsRead Sectors Read Multiple Read DMAWrite Verify Sectors Write CommandsSet Multiple Mode Write SectorsWrite DMA Write MultipleSet Features Mode Set Feature CommandsPower Mode Commands Sleep Mode Identify Drive Initialization Commands15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Format Track Seek, Format and Diagnostic CommandsExecute Drive Diagnostic Execute S.M.A.R.T A.R.T. Command SetSupport Service and SupportService Policy No Quibble ServiceInternet MaxFax ServiceCustomer Service Glossary Error Free Direct AccessDirect Memory Access Error Correction Code ECCFlux Changes PER Inch Hard ErrorHead Disk Assembly HDA File Allocation Table FATLogical Sector Phase Locked Loop PLLLogical Address Logical Block AddressingSector Pulse Signal Random Access Memory RAMRead Gate Signal Recoverable ErrorTHIN-FILM Media UN-CORRECTABLE ErrorUnrecoverable Error Write Gate Signal
Top Page Image Contents