Maxtor 91280D5, 91024D4, 90750D3, 91536D6, 91792D7, 92048D8 manual Sleep Mode

Page 56

INTERFACE COMMANDS

When enabling the Automatic Power Down sequence, the value placed in the Sector Count register is multiplied by five seconds to obtain the Time-out Interval value. If no drive commands are received from the host within the Time-out Interval, the drive automatically enters the STANDBY mode. The minimum value is 5 seconds.

TIMER VALUE

TIME-OUT PERIOD

0

Time-out disabled

 

 

1 - 240

(value * 5) seconds

 

 

241 - 251

((value - 240) * 30) minutes

252

21 minutes

253

Vendor unique period = 10

 

hours

254

Reserved

255

21 minutes, 15 seconds

While the drive is in STANDBY MODE, any commands received from the host are accepted and executed as they would in normal operation, except that the spin motor is started if required to execute a disk command. Under these conditions, the drive will set BSY when command processing would normally begin and will leave BSY set until the drive comes up to speed and the disk command can be executed. Disk commands issued while the drive is in STANDBY MODE, restarts the Time-out Interval after completing the command. A reset must be issued before attempting to issue any commands while the drive in

SLEEP MODE.

7 – 8

Image 56
Contents HA RD Drive Produc T MA Nual DiamondMax Plus Revisions Manual No Before You Begin U T I O NContents Product Specifications Handling and InstallationAT Interface Description Host Software InterfaceGlossary Interface CommandsService and Support Figures Introduction Maxtor CorporationManual Organization AbbreviationsSignal Conventions ConventionsKey Words NumberingDiamondMax Plus 5120 Key Features Product DescriptionProduct Features Functional / InterfaceOn-the-Fly Hardware Error Correction Code ECC Logical Block AddressingDefect Management Zone DMZ Software ECC CorrectionRead-Ahead Mode Cache ManagementBuffer Segmentation Automatic Write Reallocation AWRMajor HDA Components Subsystem Configuration Jumper Location/ConfigurationCylinder Limitation Dual Drive SupportProduct Specifications Drive ConfigurationPerformance Specifications Models and CapacitiesPhysical Dimensions Parameter Standard MetricPower Requirements Power Mode DefinitionsEPA Energy Star Compliance Environmental LimitsReliability Specifications Shock and VibrationCanadian Emissions Statement Safety Regulatory ComplianceRadiated Electromagnetic Field Emissions EMC Compliance Handling and Installation Hard Drive Handling PrecautionsPre-formatted Drive Important NoticeUnpacking and Inspection Multi-pack Shipping ContainerRepacking Physical InstallationRecommended Mounting Configuration Before You Begin General Requirements Mounting Drive in System Attaching Interface Power Cables System Setup Hard Drive Preparation System Hangs During Boot Interface Connector SignalAT Interface Description Pin Description SummaryPIN Name Signal Name Signal Description Pin Description TableTiming Parameters Mode PIO TimingDMA Timing Ultra DMA Timing Timing Parameters all times in nanosecondsSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Error Register Features RegisterHost Software Interface Task File RegistersSector Count Register Sector Number RegisterCylinder Number Registers Device/Head RegisterCommand Register Command Name Command Code Parameters Used SDH SummaryControl Diagnostic Registers Alternate Status RegisterDevice Control Register Digital Input RegisterInterrupt Handling Reset and Interrupt HandlingReset Handling Interface Commands Set Feature CommandsRead Verify Sectors Read CommandsRead Sectors Read DMA Read MultipleWrite Commands Set Multiple ModeWrite Sectors Write Verify SectorsWrite Multiple Write DMASet Feature Commands Set Features ModePower Mode Commands Sleep Mode Initialization Commands Identify Drive15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Format Track Seek, Format and Diagnostic CommandsExecute Drive Diagnostic A.R.T. Command Set Execute S.M.A.R.TService and Support Service PolicyNo Quibble Service SupportInternet MaxFax ServiceCustomer Service Glossary Direct Access Direct Memory AccessError Correction Code ECC Error FreeHard Error Head Disk Assembly HDAFile Allocation Table FAT Flux Changes PER InchPhase Locked Loop PLL Logical AddressLogical Block Addressing Logical SectorRandom Access Memory RAM Read Gate SignalRecoverable Error Sector Pulse SignalUN-CORRECTABLE Error Unrecoverable ErrorWrite Gate Signal THIN-FILM Media