Maxtor 80-160GB manual ATA BUS Interface Connector J1, Section C, DC Power J1, Section a

Page 24

Installation

3.4ATA BUS INTERFACE CONNECTOR (J1, SECTION C)

J1 is a three-in-one combination connector. The drive’s DC power can be applied to section A. The ATA bus interface (40-pin) uses section C. The connector is mounted on the back edge of the printed-circuit board (PCB), as shown in Figure 3-5.

Center

Key Slot

Pin 1

J1 IDE (40-Pin)/DC (4-Pin)

Combination Connector

	40-Pin IDE		4-Pin DC Power
		Pin 1	(J1 Section A)
	(J1 Section C)
			4	3	2	1

Pin 40

Figure 3-5J1 DC Power and ATA Bus Combination Connector

3.4.1DC Power (J1, Section A)

The recommended mating connectors for the +5 VDC and +12 VDC input power are listed in Table 3-3.

Table 3-3J1 Power Connector, Section A

Pin Number	Voltage Level		Mating Connector Type and Part Number (or equivalent)


		J1 Section A (4-Pin):

1	+12 VDC		4-Pin Connector: AMP P/N 1-480424-0

2	Ground Return for +12 VDC		Loose piece contacts: AMP P/N VS 60619-4
			Loose piece contacts: AMP P/N VS 60619-4
3	Ground Return for +5 VDC		Strip contacts: AMP P/N VS 61117-4

4	+5 VDC
4	+5 VDC

Note: Labels indicate the pin numbers on the connector. Pins 2 and 3 of section A are the +5 and +12 volt returns and are connected together on the drive.

Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive

3-9

Image 24

Contents ATA Revisions UL/CSA/VDE/TUV/WEEE/RoHSPatents Before You Begin Corporate HeadquartersTable Of Contents Service and Support List of Figures List of Tables Audience Manual OrganizationTerminology and Conventions ATAReferences Introduction General Description Product OverviewKEY Features Regulatory Compliance Standards Hardware Requirements Installation Space RequirementsUnpacking Instructions 220 Pack Shipping Container ATA Interface Connector Hardware Options1AT Jumper Options Cable Select CS Jumper ATA Bus Adapter CLJ Jumper Out2.1 40-Pin ATA Bus Connector ATA BUS Interface Connector J1, Section C DC Power J1, Section aATA Bus Interface Connector J1, Section C External Drive Activity LEDMounting Orientation7Mounting Screw Clearance Clearance VentilationAdapter Board Installation For Systems with AN ATA Adapter BoardConnecting the Adapter Board and the Drive Techniques in Drive Configuration 8.4-Gigabytes BarrierOperating System Limitations System Startup and Operation Model InterfaceMax LBA Capacity Drive Configuration Model Number and CapacityModel 6G080L0 6G160P0 Physical Dimensions ModelValue Power Requirements 80GB & 160GB Mode Power CurrentVoltage Tolerance Voltage TolerancePower Mode Definitions EPA Energy Star ComplianceParameter Non-Operating/StorageReliability Specifications Shock and VibrationParameter Operating Non-Operating Safety Regulatory Compliance Canadian Emissions StatementProduct Specifications Signal Cable and Connector IntroductionMechanical Interface Electrical InterfaceCommand Interface General Feature SetSupported Commands Command Command Code Feature Register2fh 3fh Identify Drive Command Word Content Description51-52 Obsolete Total number of user addressable sectors Minimum PIO transfer cycle time with Iordy flow control Minor version number See Address Offset Reserved Area Boot, Incits TR272001 = release interrupt enabled General Purpose Logging feature set supported Word Stream Access Latency DMA Security status ATA Bus Interface and ATA Commands Service and Support Getting HelpService and Support Glossary Glossary Glossary Glossary Positioner See actuator Glossary