Eicon Networks Diva 2430 manual Windows NT

Page 28

Setup: TCP/IP Setup

Page 28

Windows NT 4.0

The following procedure describes how to install TCP/IP on Windows NT 4.0.

If TCP/IP is already installed on your system, see Configuring TCP/IP (below). Note that if you have more than one adapter installed on your system, you will have to use the adapter that is in use by the Diva 2430.

Procedure

1.Click ‘Start’, ‘Settings’, ‘Control Panel’.

2.Double-click the ‘Network’ icon. The Network dialog box appears.

3.Click the ‘Protocols’ tab.

•If ‘TCP/IP’ is not listed, go to Installing TCP/IP (below).

•If ‘TCP/IP’ is listed, then the protocol is already installed. Go to Configuring TCP/IP (below).

Installing TCP/IP

1.From the ‘Protocols’ tab, click ‘Add’.

2.Select ‘TCP/IP protocol’ as your network protocol, then click ‘OK’.

3.Click ‘Yes’ to use DHCP.

4.When prompted, insert the original Windows NT installation CD and enter d:\i386 (where d: is the drive letter of your CD drive), and click ‘Continue’.

5.Do not click the ‘OK’ button yet; next you will verify your TCP/IP settings. Go to Configuring TCP/IP (below).

Configuring TCP/IP

1.Click the ‘Protocols’ tab.

2.Select ‘TCP/IP protocol’, then click ‘Properties’.

3.Select ‘Obtain an IP address from a DHCP server’.

4.Click the ‘DNS’ tab. Delete any DNS addresses are configured.

5.Click ‘OK’.

6.Restart your computer if requested to do so.

Image 28

Contents Diva 2430 Adsl Modem Fourth Edition March 206-362-04 Contents Introduction This SectionSetup and Configuration Features Adsl and Network FeaturesHardware Features Introducing the Diva 2430 Adsl ModemPackage Contents Setup Connecting to Both Ports OverviewHardware Requirements Software RequirementsConnecting the Microfilters Connecting MicrofiltersAbout Microfilters USB Setup Windows 2000, or Windows MeProcedure Connect the CablesInstall USB Drivers Setup USB Setup Test Internet Access Ethernet Setup Adsl Test Internet Access Optional Install the Diva Assistant Setup Optional Install the Diva Assistant LAN Setup Setup LAN Setup Configuring Settings via the Web Interface Logging into the Web-based Configuration InterfaceUsing the Configuration Menus ATM Settings Adsl Settings TCP/IP Setup Windows 95/98 Windows NT Windows Macintosh Mac OS 8 or later Can’t access the Internet TroubleshootingCan’t access the web-based configuration interface Power light is blinking red Using your Diva About the Diva Assistant Launching the Diva AssistantSystem Tray Icon General TabPerformance Tab Diagnostic Log TabTools Tab Indicator Lights Resetting the Device Normal ResetReset Settings to Factory Defaults Boot Monitor ModeWeb-based Configuration Interface Web-based Configuration Interface Overview Starting the Web-based Configuration Interface ‘Reset’ and ‘Logout’ buttons on the main menu ‘Save’, ‘Reset Form’, and ‘Cancel’ ButtonsGetting Help Saving and restoring configuration files Backing up Configuration Files Opening to the Firmware MaintenanceUpgrading Firmware Retrieving Firmware from the Eicon Networks Web SiteUploading New Firmware Resetting to Factory Defaults Advanced Topics Security Automatic Log Out Setting a Password System passwordErasing the system password Disable Inbound Server Requests Enabling this OptionIP Traffic Only Virtual Private Networking Setting up a VPN with Windows 95 or WindowsBefore you Begin Setting up a VPN with Windows Advanced Topics Virtual Private Networking Advanced Topics Virtual Private Networking Dialing the VPN Specifications and Regulatory Information Specifications General SpecificationsSoftware and Firmware Specifications UBR CBR Regulatory Information Declaration of Conformity Regulatory Information for the United StatesFCC Part 68 Notice Safety Notice Regulatory Information for Canada Power Consumption Safety Status TNV-3Regulatory Information for the European Union Index Index