Abit KV8 PRO user manual Install CPU and Heatsink

Page 10

2-2	Chapter 2

2-2. Install CPU and Heatsink

This motherboard provides a ZIF (Zero Insertion Force) Socket 754 to install AMD Socket 754 CPU. The CPU you bought should contain with a kit of heatsink, cooling fan, retention frame and blackplate. If that’s not the case, buy one specially designed for Socket 754.

Please refer to the figure shown here to install CPU and heatsink. (For reference only. Your Heatsink & Fan Assembly may not be exactly the same as this one.)

1.Locate the Socket 754 on this motherboard. Pull the CPU release lever sideways to unlatch and then raise it all the way up.

2.Drop the processor with its pin side down into the CPU socket. Do not use extra force to insert CPU; it only fits in one direction. Close the CPU release lever.

3.Align the Backplate Standoffs with the mounting holes on motherboard. Position the backplate onto motherboard.

4.Place the Retention Frame onto the motherboard and align it with the Backplate Standoffs.

5.Place heatsink on top of CPU, and make sure the heatsink fits properly on the retention frame.

6.Hook both sides of the Spring Clip onto the Mounting Tabs of Retention Frame. Tighten screws until the Spring Clip is fully installed.

7.Attach the fan connector of Heatsink & Fan Assembly with the CPU-FAN connector on the motherboard.

ATTENTION: Do not forget to set the correct bus frequency and multiple for your processor.

KV8 Pro

Image 10

Contents KV8 Pro Copyright and Warranty Notice KV8 ProTable Of Contents Install LAN Driver Save & Exit Setup Exit Without SavingInstall Audio Driver Install VIA USB 2.0 DriverIntroduction Features & SpecificationsIntroduction On board VT6122 10/100/1000 Mb PCI Ethernet ControllerBack Panel I/O 2x USB headers 1x CD-IN, 1x AUX-IN headerLayout Diagram KV8 Pro Install The Motherboard Hardware SetupHardware Setup Install CPU and Heatsink Bank 2, 3 DIMM2 Install System Memory128MB ~ 1GB Total System Memory 128MB ~ 2GB User’s ManualChapter Connectors, Headers and Switches FAN Connectors Page USBPWR1 Page VCC Pdif Out Internal Audio Connectors Page Chapter Hardware Setup IDE Connectors Post Code Display Page Chapter Hardware Setup System Management Bus Headers AUDIO1 Bios Setup Bios SetupChapter ΜGuru Utility User DefineChapter Back to µGuru Utility Setup Menu Temperature MonitoringBeep Temp This item selects the warning temperature limit Voltage MonitoringFan Speed Monitoring FanEQ Control Standard Cmos Features Back to Standard Cmos Features Setup Menu Page Advanced Bios Features Hard Disk Boot PriorityPage Advanced Chipset Features Back to Advanced Chipset Features Setup Menu Dram Timing Selectable Bios Setup Integrated Peripherals OnChip IDE Device Click Enter key to enter its submenuBack to Integrated Peripherals Setup Menu Back to Integrated Peripherals Setup Menu Power Management Setup Resume by Ring Page Back to PnP/PCI Configurations Setup Menu PnP/PCI ConfigurationsResources Controlled By PCI slot 1 shares IRQ signals with AGP slot PCI-1 PCI-2 PCI-3 PCI-4 PCI-5Set Password Load Fail-Safe DefaultsLoad Optimized Defaults Save & Exit SetupInstall VIA 4-in-1 Driver Appendix A. Install VIA 4-in-1 DriverFollowing screen appears Click Next Click Yes User’s Manual Appendix a Appendix B. Install Audio Driver Appendix B Appendix C. Install LAN Driver Appendix C Appendix D. Install VIA USB 2.0 Driver Click Yes Click OK Click Print to File KV8 Pro Install VIA Serial ATA RAID Driver Appendix E. Install VIA Serial ATA RAID DriverClick Next User’s Manual Appendix E Appendix F. Install Abit µGuru Driver Install Abit µGuru DriverAppendix F Appendix G. Post Code Definition Award Post Code DefinitionScreen logo InsteadInitialize the Apic for P6 class CPU Initialize InitOnbaordAUDIO Set up floppy related fields in 40hardwareInitialize InitOnboardSuperIO Assign resources to all ISA PnP devicesEnable L2 cache Enable/Disable Parity Check according to Cmos setupRead HDD boot sector information for Trend Anti-Virus code Program boot up speedAC2003 Post Code Definition KV8 Pro Appendix H. Troubleshooting Need Assistance? Appendix H User’s Manual Model OS/Application Hardware Name Brand SpecificationsProblem Description KV8 Pro Motherboard Model NoAppendix I. How to Get Technical Support How to Get Technical SupportAppendix Alt.comp.hardware.homebuilt alt.comp.hardware.pc-homebuiltFax 43-1-7346713 asguard@asguard.at Thank You Abit Computer Corporation