Abit KV8 PRO user manual Appendix H. Troubleshooting Need Assistance?

Page 73

Troubleshooting (Need Assistance?)

H-1

 

 

Appendix H. Troubleshooting (Need Assistance?)

Q & A:

Q:Do I need to clear the CMOS before I use a new motherboard to assemble my new computer system?

A:Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and then back. When you boot up your system for the first time, follow the instructions in the user's manual to load the optimized defaults.

Q:If my systems hang when I update the BIOS or set the wrong CPU parameters, what should I do?

A:Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always clear CMOS jumper before booting up again.

Q:Why the system failed to boot up and nothing was displayed on the screen after I did some over-clocking or non-standard settings inside the BIOS? Is the motherboard dead? Do I need to return it to where I bought from or go through an RMA process?

A:It should not cause hardware or permanent damage to motherboard when BIOS settings were changed from default to over-clocking or non-standard status.

We suggest the following three troubleshooting methods to discharge CMOS data, recover the hardware default status, and then make the motherboard working again. No need to bother returning the motherboard to where you bought from or go through an RMA process.

Step 1. Switch off the power supply unit and then switch it on again after one minute. If there is no power switch on the power supply unit, disconnect its power cord for one minute and then connect it back.

Press and hold the <Insert> key on the keyboard, press the power-on button to boot up system. If it works, loose the <Insert> key and hit <Del> key to enter the BIOS setup page to do the correct settings.

If the situation remains the same, repeat the procedures in Step 1 for three times, or try Step 2.

Step 2. Switch off the power supply unit or disconnect the power cord. Open the chassis cover. Locate the CCMOS jumper near the button battery. Change the jumper position from default 1-2 to 2-3 for one minute to discharge the CMOS data, and then put it back to default 1-2 position.

Close the chassis and switch on the power supply unit or plug in the power cord. Press the power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page to do the correct settings.

If the situation remains the same, try Step 3.

Step 3. The same procedure as Step 2, but in the meantime of discharging the CMOS data, pull out ATX power connectors from motherboard and remove the button battery during CMOS discharging.

User’s Manual

Image 73
Contents KV8 Pro KV8 Pro Copyright and Warranty NoticeTable Of Contents Install Audio Driver Save & Exit Setup Exit Without SavingInstall LAN Driver Install VIA USB 2.0 DriverIntroduction Features & SpecificationsIntroduction On board VT6122 10/100/1000 Mb PCI Ethernet Controller2x USB headers 1x CD-IN, 1x AUX-IN header Back Panel I/OLayout Diagram KV8 Pro Install The Motherboard Hardware SetupHardware Setup Install CPU and Heatsink 128MB ~ 1GB Install System MemoryBank 2, 3 DIMM2 Total System Memory 128MB ~ 2GB User’s ManualChapter Connectors, Headers and Switches FAN Connectors Page USBPWR1 Page VCC Pdif Out Internal Audio Connectors Page Chapter Hardware Setup IDE Connectors Post Code Display Page Chapter Hardware Setup System Management Bus Headers AUDIO1 Bios Setup Bios SetupChapter User Define ΜGuru UtilityChapter Temperature Monitoring Back to µGuru Utility Setup MenuVoltage Monitoring Beep Temp This item selects the warning temperature limitFan Speed Monitoring FanEQ Control Standard Cmos Features Back to Standard Cmos Features Setup Menu Page Hard Disk Boot Priority Advanced Bios FeaturesPage Advanced Chipset Features Back to Advanced Chipset Features Setup Menu Dram Timing Selectable Bios Setup OnChip IDE Device Click Enter key to enter its submenu Integrated PeripheralsBack to Integrated Peripherals Setup Menu Back to Integrated Peripherals Setup Menu Power Management Setup Resume by Ring Page Back to PnP/PCI Configurations Setup Menu PnP/PCI ConfigurationsResources Controlled By PCI-1 PCI-2 PCI-3 PCI-4 PCI-5 PCI slot 1 shares IRQ signals with AGP slotLoad Optimized Defaults Load Fail-Safe DefaultsSet Password Save & Exit SetupInstall VIA 4-in-1 Driver Appendix A. Install VIA 4-in-1 DriverFollowing screen appears Click Next Click Yes User’s Manual Appendix a Appendix B. Install Audio Driver Appendix B Appendix C. Install LAN Driver Appendix C Appendix D. Install VIA USB 2.0 Driver Click Yes Click OK Click Print to File KV8 Pro Install VIA Serial ATA RAID Driver Appendix E. Install VIA Serial ATA RAID DriverClick Next User’s Manual Appendix E Install Abit µGuru Driver Appendix F. Install Abit µGuru DriverAppendix F Award Post Code Definition Appendix G. Post Code DefinitionScreen logo InsteadInitialize the Apic for P6 class CPU Initialize InitOnboardSuperIO Set up floppy related fields in 40hardwareInitialize InitOnbaordAUDIO Assign resources to all ISA PnP devicesRead HDD boot sector information for Trend Anti-Virus code Enable/Disable Parity Check according to Cmos setupEnable L2 cache Program boot up speedAC2003 Post Code Definition KV8 Pro Appendix H. Troubleshooting Need Assistance? Appendix H User’s Manual Problem Description KV8 Pro OS/Application Hardware Name Brand SpecificationsModel Motherboard Model NoHow to Get Technical Support Appendix I. How to Get Technical SupportAlt.comp.hardware.homebuilt alt.comp.hardware.pc-homebuilt AppendixFax 43-1-7346713 asguard@asguard.at Thank You Abit Computer Corporation