Abit KV8 PRO user manual

Page 51

BIOS Setup	3-23

NOTE: To enable this “Power On” function, the wake-up header of [USBPWR1] and [USBPWR2] must be set to [Enabled] position. Please refer to the configuration of “Wake-up Header” [USBPWR1] and [USBPWR2] in section 2-4, chapter 2.

The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or USB type. Some PS/2 mice cannot wake up the system because of compatible problems. If the specs of your keyboard are too old, it may fail to power on.

KB Power ON Password:

This item sets the password required in order to power on your computer.

NOTE: Do not forget your password, or you will have to clear the CMOS and reset all parameters in order to utilize this function again.

Hot Key Power ON:

This item powers on the system by pressing <Ctrl> key plus one of each function key (<F1> ~ <F12>) simultaneously.

User’s Manual

Image 51

Contents KV8 Pro KV8 Pro Copyright and Warranty NoticeTable Of Contents Install VIA USB 2.0 Driver Save & Exit Setup Exit Without SavingInstall Audio Driver Install LAN DriverOn board VT6122 10/100/1000 Mb PCI Ethernet Controller Features & SpecificationsIntroduction Introduction2x USB headers 1x CD-IN, 1x AUX-IN header Back Panel I/OLayout Diagram KV8 Pro Hardware Setup Install The MotherboardHardware Setup Install CPU and Heatsink Total System Memory 128MB ~ 2GB User’s Manual Install System Memory128MB ~ 1GB Bank 2, 3 DIMM2Chapter Connectors, Headers and Switches FAN Connectors Page USBPWR1 Page VCC Pdif Out Internal Audio Connectors Page Chapter Hardware Setup IDE Connectors Post Code Display Page Chapter Hardware Setup System Management Bus Headers AUDIO1 Bios Setup Bios SetupChapter User Define ΜGuru UtilityChapter Temperature Monitoring Back to µGuru Utility Setup MenuVoltage Monitoring Beep Temp This item selects the warning temperature limitFan Speed Monitoring FanEQ Control Standard Cmos Features Back to Standard Cmos Features Setup Menu Page Hard Disk Boot Priority Advanced Bios FeaturesPage Advanced Chipset Features Back to Advanced Chipset Features Setup Menu Dram Timing Selectable Bios Setup OnChip IDE Device Click Enter key to enter its submenu Integrated PeripheralsBack to Integrated Peripherals Setup Menu Back to Integrated Peripherals Setup Menu Power Management Setup Resume by Ring Page PnP/PCI Configurations Back to PnP/PCI Configurations Setup MenuResources Controlled By PCI-1 PCI-2 PCI-3 PCI-4 PCI-5 PCI slot 1 shares IRQ signals with AGP slotSave & Exit Setup Load Fail-Safe DefaultsLoad Optimized Defaults Set PasswordAppendix A. Install VIA 4-in-1 Driver Install VIA 4-in-1 DriverFollowing screen appears Click Next Click Yes User’s Manual Appendix a Appendix B. Install Audio Driver Appendix B Appendix C. Install LAN Driver Appendix C Appendix D. Install VIA USB 2.0 Driver Click Yes Click OK Click Print to File KV8 Pro Appendix E. Install VIA Serial ATA RAID Driver Install VIA Serial ATA RAID DriverClick Next User’s Manual Appendix E Install Abit µGuru Driver Appendix F. Install Abit µGuru DriverAppendix F Award Post Code Definition Appendix G. Post Code DefinitionInstead Screen logoInitialize the Apic for P6 class CPU Assign resources to all ISA PnP devices Set up floppy related fields in 40hardwareInitialize InitOnboardSuperIO Initialize InitOnbaordAUDIOProgram boot up speed Enable/Disable Parity Check according to Cmos setupRead HDD boot sector information for Trend Anti-Virus code Enable L2 cacheAC2003 Post Code Definition KV8 Pro Appendix H. Troubleshooting Need Assistance? Appendix H User’s Manual Motherboard Model No OS/Application Hardware Name Brand SpecificationsProblem Description KV8 Pro ModelHow to Get Technical Support Appendix I. How to Get Technical SupportAlt.comp.hardware.homebuilt alt.comp.hardware.pc-homebuilt AppendixFax 43-1-7346713 asguard@asguard.at Thank You Abit Computer Corporation