Hand Held Products IT4600, IT4X80, IT4800, IT4710, IT4410 manual MicroPDF417, is the Encoded Message

Page 12
MicroPDF417

In rare instances where neither a valid Start nor Stop pattern is measurable, yet the symbol is somehow read, lines {8} and {9} are replaced by a message to that effect. The message is either:

"[F] < Start/Stop Decode Fails" in a Full Report or "Start/Stop Characters are Bad" in a Screening mode.

In Screening modes, it often occurs that none of the parameters are below the Minimum Acceptable grade. In this case, the final PQA line becomes:

"All Measurements within range".

MicroPDF417

The Full Report from a typical scan looks like the following (line numbers have been added in curly brackets):

{1} This is a typical Micro PDF417 symbol {2} >>> PQA from HHP <<<

{3} MICROPDF: 15 rows x 3 cols, 24 data & 21 chks {4} X roughly = 0.015"

{5} [A] < Row Height = 1.8 X

{6} [A] < Data Safety Margin = 100% (0 Erasures & 0 Errors)

{7} [A] < Edge Accuracy = 70%

{8} [A] < Print Growth = +4% of X

where:

{1} is the Encoded Message.

{2} is the Banner heading.

{3} identifies the Symbology, MICROPDF (or one of its derivatives: COMPOS- ITE-A, COMPOSITE-B, or TLC39), and lists other characteristics of this symbol: the height and width, and the numbers of data and check, or error correction characters.

{4} presents an approximate X-dimension.

Note: The reported X-dimension is approximate and based upon use of the IT4410LR at 4.7 in (12 cm) (see "Reading Techniques" on page 1-1). If you use different image engines, the X-dimension will vary. If you hold the reader closer than 4.7 in (12 cm), it will have the effect of reporting a larger than true X-dimension. Conversely, if you hold the reader farther away than 4.7 in (12 cm), it will have the effect of reporting a smaller than true X-dimension. Please contact HHP Application Support for additional information. Refer to Chapter 3 for contact information.

{5} lists the average Row Height, assigning the grades as:

1 - 8

Image 12
Contents User’s Guide Quick Check 2D Print Quality AssessmentDisclaimer Chapter 1 - Introduction Table of ContentsChapter 2 - Quick*View Chapter 3 - Customer SupportSymbology X-dimensionIntroduction User OperationReading Techniques Symbology/Parameter Specifics 2D PQA Reporting Full ReportScreening Report Identifying Symbol Content This is a representative PDF417 symbol PQA from HHPA Data Safety Margin = 100% 0 Erasures & 0 Errors PDF417 11 rows x 3 cols, 25 data & 8 chks ECL = 2 X roughly =2D Stacked / Multi-row PDF417Excessive Print Shrinkage -43% of where In Screening modes, this parameter is reported as Useful Row Height is Too Short 1.5X when that is the case MicroPDF417 1 is the Encoded Message2D Matrix Aztec CodeData Matrix 1 This is a representative Data Matrix symbol 2 PQA from HHP6 A Fixed Patterns 0 module errors 3 DATA MATRIX ECC200 24 x 24 modules in sizeQR Code 7 A Data Safety Margin = 100%1 This is a representative QR Code symbol 2 PQA from HHP MaxiCode 4 lists this symbols Mask Pattern and Error Correction LevelPostal Height-Modulated Bar Code Symbologies Postnet and Planet Code7 A Ok Bar Widths = 0.022 in 8 A Ok Inter-Bar Gaps = 0.023 in 4-State Codes 1 B15AJ6T 2 PQA from HHP3 4-STATEBritish 34 Bars, nominally from 38.5 to 42.3 mm. in Width 4 Bar Sequence ADHTATDAHDDAADADAADTHTADHHDATHTADHParameter Interpretation Average Bar/Gap WidthAverage Bar Height/Extension Height Table 1 Dimensional Tolerances for the Various 4-State BarData Safety Margin Bar SequenceCodeword Data and Check Codeword YieldError Correction/Error Correction Characters Error Correction Level ECLError Detection/Error Detection Characters Encoded MessageModule Errors SymbologyPrint Growth Horizontal and Vertical Row HeightX-dimension Installing Quick*View from the Web Setting Up the Imager and the Quick*View SoftwareQuick*View Quick*View Demonstration Software InstructionsTemporary Quick*View Configuration IT4600/4800/4X80IT4410/4710 Using the Quick*View Software If Communication Cannot Be EstablishedScan Data Window Obtaining Factory Service Customer SupportNorth America Latin AmericaTechnical Assistance North America/CanadaAsia Page QC2DPQA-UG Rev B