Hand Held Products IT4800, IT4X80, IT4600, IT4710, IT4410 manual MaxiCode, is the Encoded Message

Page 16

{4} lists this symbol's Mask Pattern and Error Correction Level.

{3} QR CODE: Model 2 Version 3 (29 x 29 modules)

{4} Mask Pattern Reference #3, Error Correction Level "M"

{5} Data Field: 44 data & 26 checks in 1 block(s) of GF(256)

{6} X roughly = 0.025"

{7} [A] < Data Safety Margin = 100%

{8} [A] < Horizontal Print Growth = +20% of X {9} [A] < Vertical Print Growth = +17% of X

{1} is the Encoded Message.

{2} is the Banner heading.

{3} identifies the Symbology (QR CODE) and lists the symbol's model, version and size.

{4} lists this symbol's Mask Pattern and Error Correction Level.

{5} lists the numbers of Data and Check Words and their arrangement into blocks.

{6} presents an approximate X-dimension.

Note: The reported X-dimension is approximate and based upon use of the IT4410LR at 4.7 in (12 cm) (see "Reading Techniques" on page 1-1). If you use different image engines, the X-dimension will vary. If you hold the reader closer than 4.7 in (12 cm), it will have the effect of reporting a larger than true X-dimension. Conversely, if you hold the reader farther away than 4.7 in (12 cm), it will have the effect of reporting a smaller than true X-dimension. Please contact HHP Application Support for additional information. Refer to Chapter 3 for contact information.

{7} lists the Data Safety Margin. "M" is the recommended error correction level for QR Code, so symbols encoded at "H" or "Q" will typically have safety margins exceeding 100%, while those encoded at "L" are limited to values below 50%.

{8} and {9} list the Horizontal & Vertical Print Growths, respectively.

MaxiCode

The Full Report from a typical scan looks like the following (line numbers have been added in curly brackets):

{1} This is a representative Maxicode symbol {2} >>> PQA from HHP <<<

{3} MAXICODE: Mode 4

1 - 12

Image 16

Contents User’s Guide Quick Check 2D Print Quality AssessmentDisclaimer Chapter 1 - Introduction Table of ContentsChapter 2 - Quick*View Chapter 3 - Customer SupportSymbology X-dimensionUser Operation IntroductionReading Techniques Symbology/Parameter Specifics Full Report 2D PQA ReportingScreening Report Identifying Symbol Content This is a representative PDF417 symbol PQA from HHPA Data Safety Margin = 100% 0 Erasures & 0 Errors PDF417 11 rows x 3 cols, 25 data & 8 chks ECL = 2 X roughly =PDF417 2D Stacked / Multi-rowExcessive Print Shrinkage -43% of where In Screening modes, this parameter is reported as Useful Row Height is Too Short 1.5X when that is the case MicroPDF417 1 is the Encoded Message2D Matrix Aztec CodeData Matrix 1 This is a representative Data Matrix symbol 2 PQA from HHP6 A Fixed Patterns 0 module errors 3 DATA MATRIX ECC200 24 x 24 modules in size7 A Data Safety Margin = 100% QR Code1 This is a representative QR Code symbol 2 PQA from HHP MaxiCode 4 lists this symbols Mask Pattern and Error Correction LevelPostal Height-Modulated Bar Code Symbologies Postnet and Planet Code7 A Ok Bar Widths = 0.022 in 8 A Ok Inter-Bar Gaps = 0.023 in 4-State Codes 1 B15AJ6T 2 PQA from HHP3 4-STATEBritish 34 Bars, nominally from 38.5 to 42.3 mm. in Width 4 Bar Sequence ADHTATDAHDDAADADAADTHTADHHDATHTADHParameter Interpretation Average Bar/Gap WidthAverage Bar Height/Extension Height Table 1 Dimensional Tolerances for the Various 4-State BarData Safety Margin Bar SequenceCodeword Data and Check Codeword YieldError Correction/Error Correction Characters Error Correction Level ECLError Detection/Error Detection Characters Encoded MessageModule Errors SymbologyPrint Growth Horizontal and Vertical Row HeightX-dimension Installing Quick*View from the Web Setting Up the Imager and the Quick*View SoftwareQuick*View Quick*View Demonstration Software InstructionsIT4600/4800/4X80 Temporary Quick*View ConfigurationIT4410/4710 Using the Quick*View Software If Communication Cannot Be EstablishedScan Data Window Obtaining Factory Service Customer SupportNorth America Latin AmericaNorth America/Canada Technical AssistanceAsia Page QC2DPQA-UG Rev B