Hand Held Products IT4710, IT4X80 A Ok Bar Widths = 0.022 in 8 A Ok Inter-Bar Gaps = 0.023 in

Page 18

{7} [A] (Ok) < Bar Widths = 0.022 in.

{7} [A] (Ok) < Bar Widths = 0.022 in.

{8} [A] (Ok) < Inter-Bar Gaps = 0.023 in.

{1} is the Encoded Message.

{2} is the Banner heading.

{3} identifies the Symbology, (POSTNET or PLANET Code), and lists also the symbol's size and allowed range of measured width.

{4} lists the Bar Sequence, "1" representing a tall bar and "0" representing a short one.

{5} lists the Average Height of the tall bars, specified to fall within 0.115 to

0.125 in. The grades are assigned as:

Aif within the middle 67% of the specified tolerances, else

Bif within the specified tolerances, else

Cif within a range 25% wider(!) than the specified tolerances, else

Dif within a range 50% wider(!) than the specified tolerances, else

Fotherwise

Note: These forgiving grade assignments, employed throughout the postal symbologies, reflect what are generally tight and unforgiving print specifications.

In Screening modes, this parameter is reported as ""Tall" Bars are too Short (or Long) (0.xxx in.)" when that is the case.

{6} lists the Average Height of the short bars, specified to fall within 0.040 to 0.060 in.

In Screening modes, this parameter is reported as ""Short" Bars are too Short (or Long) (0.xxx in.)" when that is the case.

{7} lists the Average Width of the bars, specified to fall within 0.015 to 0.025 in.

In Screening modes, this parameter is reported as "Bars are too Narrow (or Wide) (0.xxx in.)" when that is the case.

{8} lists the Average Space Width between bars, specified to fall within 0.012 to 0.040 in.

In Screening modes, this parameter is reported as "Spaces are too Narrow (or Wide) (0.xxx in.)" when that is the case.

1 - 14

Image 18

Contents User’s Guide Quick Check 2D Print Quality AssessmentDisclaimer Chapter 1 - Introduction Table of ContentsSymbology Chapter 2 - Quick*ViewChapter 3 - Customer Support X-dimensionIntroduction User OperationReading Techniques Symbology/Parameter Specifics 2D PQA Reporting Full ReportScreening Report A Data Safety Margin = 100% 0 Erasures & 0 Errors Identifying Symbol ContentThis is a representative PDF417 symbol PQA from HHP PDF417 11 rows x 3 cols, 25 data & 8 chks ECL = 2 X roughly =2D Stacked / Multi-row PDF417Excessive Print Shrinkage -43% of where In Screening modes, this parameter is reported as Useful Row Height is Too Short 1.5X when that is the case MicroPDF417 1 is the Encoded Message2D Matrix Aztec Code6 A Fixed Patterns 0 module errors Data Matrix1 This is a representative Data Matrix symbol 2 PQA from HHP 3 DATA MATRIX ECC200 24 x 24 modules in sizeQR Code 7 A Data Safety Margin = 100%1 This is a representative QR Code symbol 2 PQA from HHP MaxiCode 4 lists this symbols Mask Pattern and Error Correction LevelPostal Height-Modulated Bar Code Symbologies Postnet and Planet Code7 A Ok Bar Widths = 0.022 in 8 A Ok Inter-Bar Gaps = 0.023 in 3 4-STATEBritish 34 Bars, nominally from 38.5 to 42.3 mm. in Width 4-State Codes1 B15AJ6T 2 PQA from HHP 4 Bar Sequence ADHTATDAHDDAADADAADTHTADHHDATHTADHAverage Bar Height/Extension Height Parameter InterpretationAverage Bar/Gap Width Table 1 Dimensional Tolerances for the Various 4-State BarCodeword Data and Check Data Safety MarginBar Sequence Codeword YieldError Detection/Error Detection Characters Error Correction/Error Correction CharactersError Correction Level ECL Encoded MessagePrint Growth Horizontal and Vertical Module ErrorsSymbology Row HeightX-dimension Quick*View Installing Quick*View from the WebSetting Up the Imager and the Quick*View Software Quick*View Demonstration Software InstructionsTemporary Quick*View Configuration IT4600/4800/4X80IT4410/4710 Using the Quick*View Software If Communication Cannot Be EstablishedScan Data Window North America Obtaining Factory ServiceCustomer Support Latin AmericaTechnical Assistance North America/CanadaAsia Page QC2DPQA-UG Rev B