ETA Systems SM5505 manual Safety, Ansi Warning Notices, Inherent Hazards, Alerts and Labels

Page 7

Section 2 - Safety

- IMPORTANT SAFETY INSTRUCTIONS -

- SAVE THESE INSTRUCTIONS -

2.1 ANSI Warning Notices

Failure to observe reasonable precautions in the use of this product may result in fire, injury, electrocution and/or death. Please observe all notices and warnings. This equipment must be installed in accordance with all applicable national, state, county, and/or municipal codes. If you are in doubt about any phase of installation or operation, contact the manufacturer immediately for assistance. While this entire document is important, certain portions may require your special attention. These passages are clearly marked with the notices shown below. Please observe all safety notices carefully. Each has a specific meaning.

C A U T IO N in d ic a te s a p o te n tia lly h a z a rd o u s s itu a tio n w h ich , if n o t a vo id e d , co u ld re su lt in

m in o r o r m o d e ra te in ju ry . It m a y a ls o b e u s e d to

a le rt a g a in s t u n sa fe p ra c tic e s .

W A R N IN G in d ic a te s a p o te n tia lly h a z a rd o u s s itu a tio n w h ich , if n o t a vo id e d , co u ld re su lt in d e a th o r s e rio u s in ju ry .

D A N G E R in d ic a te s a n im m in e n tly h a z a rd o u s s itu a tio n w h ich , if n o t a vo id e d , w ill re s u lt in d e a th o r s e rio u s in ju ry .

2.2 Inherent Hazards

This product uses electricity and high voltages are present inside the cabinet. This product is equipped with a lockout/tagout feature on the input circuit breaker to prevent accidentally energizing the product during installa- tion, maintenance, and/or repair. This product is also equipped with safety interlock circuits, which will de- energize the product when a cover is removed. In all such cases, hazardous touch voltages will still be present at the rear of the product’s input circuit breaker where input power feeds are attached. Working on the product under such circumstances is classified under SEMI S2-0200 as a Type 4 Task. This may be changed to a Type 1 task and complete safety may be assured by disconnecting power to the product (and locking and tagging out) at the source.

Failure to follow proper safety precautions as well as intentionally defeating the safety interlocks built into the product’s design will negate the safety features designed into this product and may subject the user to death or serious injury.

2.3 Alerts and Labels

This product’s enclosure is provided with warning labels in appropriate locations to call your attention to important user information. The labels and their locations include the following:

Conditioned Power Center

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents CPC Series Conditioned Power Center Table of Contents Service and Support E a S E General Alerts and Labels SafetyAnsi Warning Notices Inherent HazardsWear protective gear before servicing internal parts Line Voltage Present With Machine Power OFFLockout/Tagout Safety InterlocksProduct Liability Conformance with Applicable Laws and RegulationsEmergency Contact Information Product Purpose Product OverviewOptional Features Standard FeaturesFeature Unpackaging PreparationPreparation Figure D Shipping Crate Disassembly 10 to 20 kVA Installation Fixed Input Circuit Breakers Outer Panel RemovalAlternate Conduit Landing Locations Main Input Circuit BreakerProgrammable Circuit Breakers Isolation TransformerFigure G Transformer Primary Voltage AdjustmentGrounding Output Voltage Fine AdjustmentFigure J Lockout/Tagout ProcedureOutput Power Connections Input Power ConnectionsModels With Optional Line Cord/Output Receptacles Energizing the Power Conditioner Restoring For ServiceOperation Orderly Shutdown Energizing the LoadConditioned Power Center Seismic Anchorage Phase Loss/Low Voltage Detection and ProtectionOptions External EMOSemi S2-0200 Certification Input Power Conductor RestraintsSemi S2-0200 Compliant EMO Options Input Circuit Breaker Trips Troubleshooting/MaintenanceConditions Requiring Troubleshooting Source Circuit Breaker TripTvss Fault LEDs Illuminate Harmonic Filter Circuit Breaker Trips Out Routine MaintenanceTechnical and Service Assistance Customer Service Service and SupportProduct Warranty CPC Series Schematic SpecificationsGPI Series 2000 Standard EMO GPI Series 2000 Semi S2 EMO Important ALL Work to be Done By a Licensed Electrician Output Voltage Fine AdjustmentTitle Rev. Letter Rel. Date Next Rev. Level Document Revision HistorySM5505- Rev. a 03/01/2006, 2006 ETA Systems39
Top Page Image Contents