Envision Peripherals NV3128 manual TechnicalSupport

Page 4

TechnicalSupport

If you need support of any kind related to your equipment, contact the local representative who sold you the product, or you may contact NVISION, Inc. directly by any of the following methods.

Telephone

Main Telephone: (530)-265-1000

 

 

Technical Support: (530) 265-1059

 

 

Sales: 800-719-1900 or (530)-265-1000

Facsimile

Main FAX Number: (530)-265-1010

 

 

Sales: (530)-265-1021

 

Email

Technical Support: support@nvision1.com

 

Sales: sales@nvision1.com

 

Postal Addresses

ShippingAddress:

MailingAddress:

 

NVISION, Inc.

NVISION, Inc.

 

125 Crown Point Court

PO Box 1658

 

Grass Valley, CA 95945

Nevada City, CA 95959

FCC(USA)ComplianceStatement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference in which case the user will be required to correct the interference at their own expense.

EuropeanCommunity(CE)DeclarationofConformance

Some or all of the equipment described in this manual has been designed to conform with the required safety and emissions standards of the European Community. Products tested and verified to meet these standards are marked as required by law with the CE mark.

When shipped into member countries of the European Community, this equipment is accompanied by authentic copies of original Declarations of Conformance on file in NVISION corporate headquarters in Nevada City, California, USA.

Image 4
Contents Nvision PrintingHistory WarrantyStatement TechnicalSupport ImportantSafeguardsandNotices Page Page NorthAmericanPowerSupplyCords Tableofcontents Page Generalinformation NV3128 RS-422A Machine-Control Data Switch Generalinformation GeneralArchitecture Background NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch Solution Dynamic Ports Crosspointarchitecture NV3128 RS-422A Machine-Control Data Switch Multidrop Command Chains PhysicalSystem Specifications Ancillary Equipment1NV3128SPECIFICATIONS Installation NV3128 RS-422A Machine-Control Routing Switch Chapter TWO Installation NV3128 RS-422A Machine-Control Routing Switch Frame Installation Universal Control or Command Interpreter Partitioning ObsoletePartition DIP Switches Obsolete Settings RE-INITIALIZE BIT/MULTIDROP Enable s7Matrix Control II Jumpers Obsolete Input Length s8-s5RS-422A RS-232 Configuring the Diagnostic Interface Obsolete Parallel Interface ObsoleteJumper Enabled Disabled Configuring the Reference Input Reference Input Ground ObsoleteCabling the Serial Command Interface Cabling the NV3128PIN RS232 Obsolete RS-232 DCE VS. DTE Decision ObsoletePIN Connector Adding a Redundant Controller Implementing HOT Changeover ObsoletePC Diagnostic Interface UNIDIAG/NVUTILS Cabling CompleteRear Connections NEW Frame Rear Ections OLD Frame Rearconnections OLD Frame PC-BASED Software Installation Obsolete InstallationGeneral NvtakeSoftware Installation Fixed Disk Sample Install SessionHardware Configuration Operation from a Floppy DiskOperation NV3128 RS-422A Machine Control Data Routing Switch Operations Connection NotesPOINT-TO-POINT Connection Rules Multidrop Connection RulesComputer Utilities Obsolete Operating Instructions Nvtake Obsolete InvocationOperations F3 Change Router LevelF1 Sending a Single Take F9 Build a Salvo Table F10 Load a Salvo from Disk F2 Send a SalvoF5 Query Multiple Connections F6 List Destinations Connected to a SourceOperating Instructions Nvmap Obsolete OperationNV3128 RS-422A Machine Control Data Routing Switch Screen NV3128 RS-422A Machine Control Data Routing Switch Theoryofoperation NV3128 RS-422A Machine-Control Data Routing Switch System Control StructureNV3128 RS-422A Machine-Control Data Routing Switch 1 I/O Connector Interface Signal BackplaneCircuit Operation Assy EM0038-XXCrosspoint Module Assy EM0041-XX Input DataCrosspoints Output Data4 I/O Assembly EM0040-XX Mapping Parallel Interface Command Interpreter only Power RegulationAsynchronous Timing PartitioningPower Supply Assy PS2001-XX NV3128 RS-422A Machine-Control Data Routing Switch NV3128 RS-422A Machine-Control Data Routing Switch Maintenanceand Troubleshooting NV3128 RS-422A Machine Control Data Routing Switch Customer Support Scheduled MaintenanceReliability Isolating Faults TroubleshootingPower Signal Path Mapping and Command ProblemsNV3128 RS-422A Machine Control Data Routing Switch Glossary NV3128 RS-422A Machine-Control Data Routing Switch AES/EBU MOV Vcxo NV3128 RS-422A Machine-Control Data Routing Switch Index NV3128 RS-422A Machine-Control Data Switch Index-2 Index NV3128 RS-422A Machine-Control Data Switch Index-4 NV3128 RS-422A Machine-Control Data Switch Index-5 NV3128 RS-422A Machine-Control Data Switch Index-6