Envision Peripherals manual NV3128 RS-422A Machine-Control Data Switch Index-4

Page 90

H

HDTV G-3

HDVS G-3

Hybrid G-3

I

I/O	G-3
I/O Assembly (theory)		4-7
I/O Interface Modules		4-5
IC	G-3
Installation, Hardware		2-3

J

Jumper and Switch Settings 2-6 Jumper J1 - 115/230 VAC 4-10

L

LED G-3

M

Maintenance 5-3

Monaural G-3

MOV G-4

MUX G-4

N

Nm G-4
NTSC	G-4
NVMAP		3-5
NVTAKE		3-5
O
Operating Instructions, NVMAP				3-11
Operating Instructions, NVTAKE				3-6
Oversampling G-4
P
PAL G-4
Parallel Interface 2-11
Partitioning 2-6
Power Supply (theory)			4-10
PROM	G-4
PWM	G-4
R
RAM	G-4
Redundant Controller			2-18

Reference Input, Configuring 2-13

NV3128 RS-422A Machine-Control Data Switch

Index-4

Image 90

Contents Nvision PrintingHistory WarrantyStatement TechnicalSupport ImportantSafeguardsandNotices Page Page NorthAmericanPowerSupplyCords Tableofcontents Page Generalinformation NV3128 RS-422A Machine-Control Data Switch Generalinformation GeneralArchitecture Background NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch Solution Dynamic Ports Crosspointarchitecture NV3128 RS-422A Machine-Control Data Switch Multidrop Command Chains PhysicalSystem Specifications Ancillary Equipment1NV3128SPECIFICATIONS Installation NV3128 RS-422A Machine-Control Routing Switch Chapter TWO Installation NV3128 RS-422A Machine-Control Routing Switch Frame Installation Universal Control or Command Interpreter Partitioning ObsoletePartition DIP Switches Obsolete Settings RE-INITIALIZE BIT/MULTIDROP Enable s7Matrix Control II Jumpers Obsolete Input Length s8-s5RS-422A RS-232 Configuring the Diagnostic Interface Obsolete Parallel Interface ObsoleteJumper Enabled Disabled Configuring the Reference Input Reference Input Ground ObsoleteCabling the Serial Command Interface Cabling the NV3128PIN RS232 Obsolete RS-232 DCE VS. DTE Decision ObsoletePIN Connector Adding a Redundant Controller Implementing HOT Changeover ObsoletePC Diagnostic Interface UNIDIAG/NVUTILS Cabling CompleteRear Connections NEW Frame Rear Ections OLD Frame Rearconnections OLD Frame General PC-BASED Software Installation ObsoleteInstallation NvtakeSoftware Installation Fixed Disk Sample Install SessionHardware Configuration Operation from a Floppy DiskOperation NV3128 RS-422A Machine Control Data Routing Switch Operations Connection NotesPOINT-TO-POINT Connection Rules Multidrop Connection RulesComputer Utilities Obsolete Operations Operating Instructions Nvtake ObsoleteInvocation F3 Change Router LevelF1 Sending a Single Take F9 Build a Salvo Table F10 Load a Salvo from Disk F2 Send a SalvoF5 Query Multiple Connections F6 List Destinations Connected to a SourceOperating Instructions Nvmap Obsolete OperationNV3128 RS-422A Machine Control Data Routing Switch Screen NV3128 RS-422A Machine Control Data Routing Switch Theoryofoperation NV3128 RS-422A Machine-Control Data Routing Switch System Control StructureNV3128 RS-422A Machine-Control Data Routing Switch Circuit Operation 1 I/O Connector InterfaceSignal Backplane Assy EM0038-XXCrosspoints Crosspoint Module Assy EM0041-XXInput Data Output Data4 I/O Assembly EM0040-XX Mapping Asynchronous Timing Parallel Interface Command Interpreter onlyPower Regulation PartitioningPower Supply Assy PS2001-XX NV3128 RS-422A Machine-Control Data Routing Switch NV3128 RS-422A Machine-Control Data Routing Switch Maintenanceand Troubleshooting NV3128 RS-422A Machine Control Data Routing Switch Scheduled Maintenance Customer SupportReliability Troubleshooting Isolating FaultsPower Signal Path Mapping and Command ProblemsNV3128 RS-422A Machine Control Data Routing Switch Glossary NV3128 RS-422A Machine-Control Data Routing Switch AES/EBU MOV Vcxo NV3128 RS-422A Machine-Control Data Routing Switch Index NV3128 RS-422A Machine-Control Data Switch Index-2 Index NV3128 RS-422A Machine-Control Data Switch Index-4 NV3128 RS-422A Machine-Control Data Switch Index-5 NV3128 RS-422A Machine-Control Data Switch Index-6