Envision Peripherals NV3128 manual Operation from a Floppy Disk, Hardware Configuration

Page 48

OPERATION FROM A FLOPPY DISK

A. Copy the program files supplied to a blank floppy.

B. Invoke either program from the floppy. Edited map, config and salvo files will be saved to the floppy in the course of the program session.

C. Remove the floppy and store it safely.

HARDWARE CONFIGURATION

A.Refer to "Configuring the Diagnostic Interface" earlier in this section to configure the diagnostic interface for RS-232 operation. Additionally, configure the serial controller data port for RS-232 operation if the use of NVTake is anticipated.

B.Connect the RS-232 cable to the computer serial port, COM1 or COM2, and to the appropriate connector on the router Control Interface.

·NVMap communicates with the diagnostic data port J400, located on the front of the Command Interface Module.

·NVTake communicates with the RS422/RS232 Command Data Port at the rear of the frame.

NV3128 RS-422A Machine-Control Routing Switch

2-24

Image 48

Contents Nvision PrintingHistory WarrantyStatement TechnicalSupport ImportantSafeguardsandNotices Page Page NorthAmericanPowerSupplyCords Tableofcontents Page Generalinformation NV3128 RS-422A Machine-Control Data Switch Generalinformation GeneralArchitecture Background NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch Solution Dynamic Ports Crosspointarchitecture NV3128 RS-422A Machine-Control Data Switch Multidrop Command Chains PhysicalSystem Specifications Ancillary Equipment1NV3128SPECIFICATIONS Installation NV3128 RS-422A Machine-Control Routing Switch Chapter TWO Installation NV3128 RS-422A Machine-Control Routing Switch Frame Installation Universal Control or Command Interpreter Partitioning ObsoletePartition DIP Switches Obsolete Settings RE-INITIALIZE BIT/MULTIDROP Enable s7Matrix Control II Jumpers Obsolete Input Length s8-s5RS-422A RS-232 Configuring the Diagnostic Interface Obsolete Parallel Interface ObsoleteJumper Enabled Disabled Configuring the Reference Input Reference Input Ground ObsoleteCabling the Serial Command Interface Cabling the NV3128PIN RS232 Obsolete RS-232 DCE VS. DTE Decision ObsoletePIN Connector Adding a Redundant Controller Implementing HOT Changeover ObsoletePC Diagnostic Interface UNIDIAG/NVUTILS Cabling CompleteRear Connections NEW Frame Rear Ections OLD Frame Rearconnections OLD Frame PC-BASED Software Installation Obsolete InstallationGeneral NvtakeSoftware Installation Fixed Disk Sample Install SessionHardware Configuration Operation from a Floppy DiskOperation NV3128 RS-422A Machine Control Data Routing Switch Operations Connection NotesPOINT-TO-POINT Connection Rules Multidrop Connection RulesComputer Utilities Obsolete Operating Instructions Nvtake Obsolete InvocationOperations F3 Change Router LevelF1 Sending a Single Take F9 Build a Salvo Table F10 Load a Salvo from Disk F2 Send a SalvoF5 Query Multiple Connections F6 List Destinations Connected to a SourceOperating Instructions Nvmap Obsolete OperationNV3128 RS-422A Machine Control Data Routing Switch Screen NV3128 RS-422A Machine Control Data Routing Switch Theoryofoperation NV3128 RS-422A Machine-Control Data Routing Switch System Control StructureNV3128 RS-422A Machine-Control Data Routing Switch 1 I/O Connector Interface Signal BackplaneCircuit Operation Assy EM0038-XXCrosspoint Module Assy EM0041-XX Input DataCrosspoints Output Data4 I/O Assembly EM0040-XX Mapping Parallel Interface Command Interpreter only Power RegulationAsynchronous Timing PartitioningPower Supply Assy PS2001-XX NV3128 RS-422A Machine-Control Data Routing Switch NV3128 RS-422A Machine-Control Data Routing Switch Maintenanceand Troubleshooting NV3128 RS-422A Machine Control Data Routing Switch Scheduled Maintenance Customer SupportReliability Troubleshooting Isolating FaultsPower Signal Path Mapping and Command ProblemsNV3128 RS-422A Machine Control Data Routing Switch Glossary NV3128 RS-422A Machine-Control Data Routing Switch AES/EBU MOV Vcxo NV3128 RS-422A Machine-Control Data Routing Switch Index NV3128 RS-422A Machine-Control Data Switch Index-2 Index NV3128 RS-422A Machine-Control Data Switch Index-4 NV3128 RS-422A Machine-Control Data Switch Index-5 NV3128 RS-422A Machine-Control Data Switch Index-6