Envision Peripherals NV3128 manual Operating Instructions Nvtake Obsolete, Invocation, Operations

Page 54

3.2.1 OPERATING INSTRUCTIONS - NVTAKE (OBSOLETE)

INVOCATION:

NVTAKE [H U V E R] [12] [960038400]

Where argument 1 is the router control protocol from the following list:

H = Horiz on control protocol

U = Utah Scientific

V = Vistek

E = ESBus

R = BTS

and argument 2 is the communications port, default = COM1.Argument 3 is the serial ports’s baud rate. Default = 9600 Invoking NVTAKE with no arguments displays the program’s syntax summary.

Figure 3.1 illustrates the basic NVTake screen.

OPERATIONS

The various functions of the program are invoked with function keys from the following list:

F1 Send a single take

F2 Send a salvo of takes

F3 Change to level to which the controller sends commands F4 Query a single crosspoint (Vistek protocol only)

F5 List 10 sequential crosspoint connections. (Vistek protocol only)

F6 Listalldestinationsconnectedtoasinglesource.(Vistekprotocolonly)

F3 CHANGE ROUTER LEVEL

The F3 function key allows changing the level to which the controller’s commands are issued. The level IDs of most routing protocols are numeric. Vistek uses the alpha characters A-Z. Again, point-to-point connections are addressed on level one. Connections involving multiple destinations are addressed on level two.

NV3128 RS-422A Machine Control Data Routing Switch

3-6

Image 54
Contents Nvision PrintingHistory WarrantyStatement TechnicalSupport ImportantSafeguardsandNotices Page Page NorthAmericanPowerSupplyCords Tableofcontents Page Generalinformation NV3128 RS-422A Machine-Control Data Switch Generalinformation GeneralArchitecture Background NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch NV3128 RS-422A Machine-Control Data Switch Solution Dynamic Ports Crosspointarchitecture NV3128 RS-422A Machine-Control Data Switch Multidrop Command Chains PhysicalSystem Specifications Ancillary Equipment1NV3128SPECIFICATIONS Installation NV3128 RS-422A Machine-Control Routing Switch Chapter TWO Installation NV3128 RS-422A Machine-Control Routing Switch Frame Installation Universal Control or Command Interpreter Partitioning ObsoletePartition DIP Switches Obsolete Settings RE-INITIALIZE BIT/MULTIDROP Enable s7Matrix Control II Jumpers Obsolete Input Length s8-s5RS-422A RS-232 Configuring the Diagnostic Interface Obsolete Parallel Interface ObsoleteJumper Enabled Disabled Configuring the Reference Input Reference Input Ground ObsoleteCabling the Serial Command Interface Cabling the NV3128PIN RS232 Obsolete RS-232 DCE VS. DTE Decision ObsoletePIN Connector Adding a Redundant Controller Implementing HOT Changeover ObsoletePC Diagnostic Interface UNIDIAG/NVUTILS Cabling CompleteRear Connections NEW Frame Rear Ections OLD Frame Rearconnections OLD Frame General PC-BASED Software Installation ObsoleteInstallation NvtakeSoftware Installation Fixed Disk Sample Install SessionHardware Configuration Operation from a Floppy DiskOperation NV3128 RS-422A Machine Control Data Routing Switch Operations Connection NotesPOINT-TO-POINT Connection Rules Multidrop Connection RulesComputer Utilities Obsolete Operations Operating Instructions Nvtake ObsoleteInvocation F3 Change Router LevelF1 Sending a Single Take F9 Build a Salvo Table F10 Load a Salvo from Disk F2 Send a SalvoF5 Query Multiple Connections F6 List Destinations Connected to a SourceOperating Instructions Nvmap Obsolete OperationNV3128 RS-422A Machine Control Data Routing Switch Screen NV3128 RS-422A Machine Control Data Routing Switch Theoryofoperation NV3128 RS-422A Machine-Control Data Routing Switch System Control StructureNV3128 RS-422A Machine-Control Data Routing Switch Circuit Operation 1 I/O Connector InterfaceSignal Backplane Assy EM0038-XXCrosspoints Crosspoint Module Assy EM0041-XXInput Data Output Data4 I/O Assembly EM0040-XX Mapping Asynchronous Timing Parallel Interface Command Interpreter onlyPower Regulation PartitioningPower Supply Assy PS2001-XX NV3128 RS-422A Machine-Control Data Routing Switch NV3128 RS-422A Machine-Control Data Routing Switch Maintenanceand Troubleshooting NV3128 RS-422A Machine Control Data Routing Switch Scheduled Maintenance Customer SupportReliability Troubleshooting Isolating FaultsPower Signal Path Mapping and Command ProblemsNV3128 RS-422A Machine Control Data Routing Switch Glossary NV3128 RS-422A Machine-Control Data Routing Switch AES/EBU MOV Vcxo NV3128 RS-422A Machine-Control Data Routing Switch Index NV3128 RS-422A Machine-Control Data Switch Index-2 Index NV3128 RS-422A Machine-Control Data Switch Index-4 NV3128 RS-422A Machine-Control Data Switch Index-5 NV3128 RS-422A Machine-Control Data Switch Index-6