Efficient Networks 5200 Series manual Configuring Computer Network Settings, Windows 95 / 98 / ME

Page 17

SpeedStream Router User Guide

Configuring Computer Network Settings

To access the Internet through the SpeedStream router, the TCP/IP protocol must be installed on your computer. If TCP/IP is not already installed on your computer, refer to your system documentation or online help for instructions.

The default network settings for the SpeedStream router are:

IP Address:	192.168.254.254
Subnet Mask:	255.255.255.0

Windows 95 / 98 / ME

1.On the Windows taskbar, click Start, point to Settings, and then click Control Panel.

The Windows Control Panel displays.

2.In Control Panel, double-click Network. The Network dialog box displays.

3.On the Configuration tab of the Network dialog box, select the TCP/IP entry for your Ethernet adapter; then click Properties.

The TCP/IP Properties dialog box displays.

Note The components list for your computer may differ from this screenshot.

9

Image 17

Contents Router User Guide Software License General Provisions Contents Viewing Status Screens Iii 51-57 List of IllustrationsSpeedStream Router User Guide Hardware Description IntroductionAbout the SpeedStream Router Features and BenefitsSession Tracking General Safety GuidelinesFirewall Security Hardware Installation Installing the RouterBasic Installation Procedure Minimum System RequirementsIn-Line Filter Installing Line FiltersRecording System Settings Two-to-One Adapter Connecting the CablesWall-Mount Filter Ethernet Installation Method USB Installation Method TCP/IP Properties dialog box displays Configuring Computer Network SettingsWindows 95 / 98 / ME TCP/IP Properties dialog box, click the IP Address tab Windows NT Double-clickNetwork and Dial-up Connections WindowsWindows XP Navigating the Web Interface Getting StartedLevel SnoozeLog Screen Navigation ElementsIP Filter Rules To log on to the Web interface for the first time Logging On to the Web InterfaceLogging On to a PPP Session Entering the Network PasswordService Name Access ConcentratorTo specify the host configuration settings Customizing Router SettingsClick Save Settings HostDhcp Configuration Options To specify the Dhcp configuration settings To change the user name or password User Setup System LoginTo configure the Time Client Time Client Configuration OptionsTime Client Static RoutesTo disable NAT and Napt To access the NAT/NAPT Configuration screenTo enable NAT and specify a destination IP address NAT/NAPT ServerPort Forwarding Port Forwarding Configuration OptionsTo enable Napt To delete an existing entry To edit an existing port forwarding configurationTo delete all entries in the table To add a port forwarding entryFirewall Security Levels FirewallFirewall Snooze Control DMZ SettingsDMZ Configuration Options To enable DMZ and specify an accessible computer On the Firewall DMZ Configuration screen, click Disable DMZ To disable DMZCustom IP Filter Rules Cloning a Rule DefinitionCustom IP Filter Configuration Firewall Simple Setup screenCreating Custom IP Filter Rules Fill in the following informationIf TCP/UDP chosen in , select the desired rule options Select a protocol to filterSpecify Source Port Operator options Specify Destination Port Operator optionsTypes of Attack BackgroundADS Configuration Options Select Enable Attack Detection To enable ADSTo save the new settings To filter, or drop, a packet typeRFC2684 RFC2684 Configuration OptionsTo configure RFC2684 settings UPnP Configuration Options Bridge ModeTo configure UPnP settings UPnP Universal Plug and PlayRIP Routing Information Protocol RIP Configuration OptionsTo enable bridge mode System Log To configure RIP settingsLAN Servers To configure the System Log RebootSystem Log Configuration Options Firmware Update ResetTo reset the router To update the router firmwareClick Run Diagnostics at the bottom of the screen DiagnosticsTo cancel the reset System Summary Viewing Status ScreensFirewall Log Interface MapTo display the Interface Map Interface Map Interface Map screen displaysStatus and Statistics Screens To update the displayATM/AAL Status/Statistics To display the System Log screenEthernet Status/Statistics DSL Status/StatisticsRoutes USB Status/StatisticsInterpreting the LED Display TroubleshootingBasic Troubleshooting Steps Pwr LED Not Lit Resolving Specific IssuesContacting Technical Support Attack Detection System Configuration Data SheetsAdministrative User Setup Firewall Custom IP Filter Configuration Firewall DMZ Firewall Snooze Control Firewall LevelPPP Login Static Route RIPUPnP Technical Specifications Protocol Firewall Security LevelsNeed for Speed VNC Acronyms Acronyms and Technical ConceptsMAC address Rx ErrorsOctet PPPoETechnical Concepts Dhcp Dynamic Host Configuration Protocol Icsa 3.0a-compliancy PPP Point-to-Point Protocol Index Data Sheets See Configuration Data Sheets PPP Network TCP